CompTIA
Checkpoint
ISC
HP
Dell
EC-Council
EXIN
Fortinet
ITIL®
Juniper
PMI
Microsoft
VMware
Avaya
Google
Salesforce
Amazon
Palo Alto Networks
Certiport
ISC2
All Vendors
  2. Home
  3. Exams
  4. Checkpoint
  5. 156-315.81.20

Free 156-315.81.20 Exam Braindumps (page: 23)

Page 23 of 42
PDF with 164 Questions

What destination versions are supported for a Multi-Version Cluster Upgrade?

  1. R77.30 and later
  2. R80.10 and Later
  3. R70 and Later
  4. R76 and later

Answer(s): B



Which command can you use to verify the number of active concurrent connections?

  1. fw conn all
  2. show all connections
  3. fw ctl pstat
  4. show connections

Answer(s): C



Under which file is the proxy arp configuration stored?

  1. $FWDIR/state/_tmp/proxy.arp on the security gateway
  2. $FWDIR/conf/local.arp on the management server
  3. $FWDIR/conf/local.arp on the gateway
  4. $FWDIR/state/proxy_arp.conf on the management server

Answer(s): C



What are the correct steps upgrading a HA cluster (M1 is active, M2 is passive) using Multi-Version Cluster(MVC)Upgrade?

  1. 1) In SmartConsole, change the version of the cluster object
    2) Upgrade the passive node M2 to R81.20
    3) Enable the MVC mechanism on the upgraded R81.20 Cluster Member M2 in CLISH: set cluster member mvc on
    4) Install the Access Control Policy and make sure that the installation will not stop if installation on one cluster member fails
    5) After examine the cluster states upgrade node M1 to R81.20
    6) On each Cluster Member, disable the MVC mechanism and Install the Access Control Policy SmartConsole, change the version of the cluster object,
  2. 1) Enable the MVC mechanism on both cluster members #cphaprob mvc on
    2) Upgrade the passive node M2 to R81.20
    3) In SmartConsole, change the version of the cluster object
    4) Install the Access Control Policy
    5) After examine the cluster states upgrade node M1 to R81.20
    6) On each Cluster Member, disable the MVC mechanism and Install the Access Control Policy
  3. 1) Enable the MVC mechanism on both cluster members in CLISH: set cluster member mvc on
    2) Upgrade the passive node M2 to R81.20
    3) In SmartConsole, change the version of the cluster object
    4) Install the Access Control Policy and make sure that the installation will not stop if installation on one cluster member fails
    5) After examine the cluster states upgrade node M1 to R81.20
    6) On each Cluster Member, disable the MVC mechanism
  4. 1) Upgrade the passive node M2 to R81.20
    2) Enable the MVC mechanism on the upgraded R81.20 Cluster Member M2 #cphaconf mvc on
    3) In SmartConsole, change the version of the cluster object
    4) Install the Access Control Policy
    5) After examine the cluster states upgrade node M1 to R81.20
    6) On each Cluster Member, disable the MVC mechanism and Install the Access Control Policy upgrade the passive node M2 to R81.20

Answer(s): A



Page 23 of 42



Post your Comments and Discuss Checkpoint 156-315.81.20 exam with other Community members:

Catho commented on September 25, 2024
I blindly trusted this site and purchased the full version. Well I am happy I did. Now I acquired my certificate and pass my exam.
EUROPEAN UNION
upvote

Gorbender commented on September 25, 2024
There are some new questions in this exam which are not present in this exam dumps. But about 75 to 80% of the questions are there. It was enough for me to pass.
INDIA
upvote

Nik commented on September 25, 2024
Wonderful service and content. Thank you for giving me the 50% discount.
GERMANY
upvote