Cisco®
CompTIA
Checkpoint
ISC
EC-Council
EXIN
Fortinet
ITIL®
Juniper
Microsoft
VMware
Avaya
SAP
Google
Salesforce
Amazon
Palo Alto Networks
ISC2
Splunk®
All Vendors
  2. Home
  3. Exams
  4. Cisco®
  5. 200-301

Free Cisco® 200-301 Exam Braindumps (page: 144)

Page 70 of 350
PDF with 1395 Questions

Which interface mode must be configured to connect the lightweight APs in a centralized architecture?

  1. WLAN dynamic
  2. trunk
  3. access
  4. management

Answer(s): C

Explanation:

While the Cisco WLCs always connect to 802.1Q trunks, Cisco lightweight APs do not understand VLAN tagging and should only be connected to the access ports of the neighbor switch.
This is an example switch port configuration from the Catalyst 3750: interface GigabitEthernet1/0/22 description Access Port Connection to Cisco Lightweight AP switchport access vlan 5 switchport mode access no shutdown


Reference:

https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719-wlc-lwap-config.html



Refer to the exhibit.


The following must be considered:
-SW1 is fully configured for all traffic.
-The SW4 and SW9 links to SW1 have been configured.
-The SW4 interface Gi0/1 and Gi0/0 on SW9 have been configured.
-The remaining switches have had all VLANs added to their VLAN database.

Which configuration establishes a successful ping from PC2 to PC7 without interruption to traffic flow between other PCs?

  1. SW4 interface Gi0/7 switchport mode trunk switchport trunk allowed vlan 108 ! interface Gi/0/2 switchport mode access switchport access vlan 14 SW11# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108 ! interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108 SW9# interface Gi0/2 switchport mode access switchport access vlan 14
  2. SW4 interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108 SW11# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108 !! interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108 SW9# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14
  3. SW4 interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14 SW11# interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14 SW9# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 108
  4. SW4 interface Gi/0/2 switchport mode access switchport access vlan 14 SW11# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14 ! interface Gi0/0 switchport mode access switchport access vlan 14 ! interface Gi0/1 switchport mode trunk SW9# interface Gi0/2 switchport mode access switchport access vlan 14

Answer(s): B



Refer to the exhibit. The network administrator must prevent the switch Cat9K-2 IP address from being visible in LLDP without disabling the protocol. Which action must be taken to complete the task?

  1. Configure the no lldp mac-phy-cfg command globally on Cat9K-2.
  2. Configure the no lldp receive command on interface G1/0/21 on Cat9K-1.
  3. Configure the no lldp transmit command on interface G1/0/21 on Cat9K-1.
  4. Configure the no lldp tlv-select management-address command globally on Cat9K-2.

Answer(s): D



Refer to the exhibit. An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?

  1. SW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#no switchport trunk allowed vlan 3 SW1(config-if)#switchport trunk allowed vlan 2
  2. SW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport trunk native vlan 2 SW1(config-if)#switchport trunk allowed vlan 3
  3. SW1(config)#interface fa0/2 SW1(config-if)#no switchport mode trunk SW1(config-if)#no switchport trunk allowed vlan 3 SW1(config-if)#switchport mode access
  4. SW1(config)#interface fa0/1 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport access vlan 3 SW1(config-if)#switchport trunk allowed vlan 2

Answer(s): C






Post your Comments and Discuss Cisco® 200-301 exam prep with other Community members:

200-301 Exam Discussions & Posts