support@Free-Braindumps.com
Register Login
Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
CrowdStrike
Anthropic
All Vendors
  1. Home
  2. Exams
  3. Cisco
  4. 350-401

Free 350-401 Exam Braindumps
Implementing Cisco Enterprise Network Core Technologies (ENCOR) Questions 486–490 (page: 99)

Updated On: 10-Feb-2026
Page 99 of 193
PDF with 1067 Questions

What is the function of vBond in a Cisco SD-WAN deployment?

  1. initiating connections with SD-WAN routers automatically
  2. pushing of configuration toward SD-WAN routers
  3. onboarding of SD-WAN routers into the SD-WAN overlay
  4. gathering telemetry data from SD-WAN routers

Answer(s): A



Refer to the exhibit.


A network administrator configured RSPAN to troubleshoot an issue between switch 1 and switch2. The switches are connected using interface GigabitEthernet 1/1. An external packet capture device is connected to swich2 interface GigabitEthernet 1/2. Which two commands must be added to complete this configuration? (Choose two.)


  1. switch2(config-if)#
    switchport trunk allowed vlan 10,20,30,40,50,60,70-80

  2. switch2(config)# monitor session 1 source remote vlan 70
    switch2(config)# monitor session 1 destination interface GigabitEthernet1/2

  3. switch1(config)# interface GigabitEthernet 1/1
    switch1 (config-if)#
    switchport mode access
    switch1 (config-if)#
    switchport access vlan 10
    switch2(config)# interface GigabitEthernet 1/1
    switch2(config-if)#
    switchport mode access
    switch2(config-if)#
    switchport access vlan 10

  4. switch2(config)# monitor session 2 destination vlan 10

  5. switch2(config)# monitor session 1 source remote vlan 70
    switch2(config)# monitor session 1 destination interface GigabitEthernet1/1

Answer(s): A,B

Explanation:

Switch2 is not allowing VLAN 70 which is used on Switch1 for RSPAN
so we must allow it -> Option A is correct (although it would not allow VLAN 81 to 90 to go through).
“An external packet capture device is connected to switch2 interface GigabitEthernet1/2” so we must configure
Gi1/2 as the destination port.
For your information, this is how to configure Remote SPAN (RSPAN) feature on two switches. Traffic on
FastEthernet0/1 of Switch 1 will be sent to Fa0/10 of Switch2 via VLAN 40.
+ Configure on both switches
Switch1,2(config)#vlan 40
Switch1,2(config-vlan)#remote-span
+ Configure on Switch1
Switch1(config)# monitor session 1 source interface FastEthernet 0/1
Switch1(config)# monitor session 1 destination remote vlan 40
+ Configure on Switch2
Switch2(config)#monitor session 5 source remote vlan 40
Switch2(config)# monitor session 5 destination interface FastEthernet 0/10



Which function does a Cisco SD-Access extended node perform?

  1. provides fabric extension to nonfabric devices through remote registration and configuration
  2. performs tunneling between fabric and nonfabric devices to route traffic over unknown networks
  3. used to extend the fabric connecting to downstream nonfabric enabled Layer 2 switches
  4. in charge of establishing Layer 3 adjacencies with nonfabric unmanaged node

Answer(s): C



Which router is elected the IGMP Querier when more than one router is in the same LAN segment?

  1. The router with the shortest uptime.
  2. The router with the longest uptime.
  3. The router with the highest IP address.
  4. The router with the lowest IP address.

Answer(s): D



DRAG DROP (Drag and Drop is not supported)
Drag and drop the characteristics from the left onto the switching mechanisms they describe on the right.
Select and Place:

  1. See Explanation section for answer.

Answer(s): A

Explanation:



  PDF
Viewing page 99 of 193
Viewing questions 491 - 495 out of 1067 questions


Post your Comments and Discuss Cisco 350-401 exam prep with other Community members:

AI Tutor AI Tutor 👋 I’m here to help!