QUESTION: 113

A company wants to deploy software to all users, Out very few of men will be using the software at any one point in time.
Which of the following licensing models would be BEST lot the company?

Per site
Per concurrent user
Per core
Per instance

Answer(s): B

Explanation:

Per concurrent user licensing is a model that allows a fixed number of users to access the software at any one point in time. This model is best for the company that wants to deploy software to all users,

but very few of them will be using the software at any one point in time. This way, the company can save money by paying only for the number of simultaneous users, rather than for every user who has access to the software. Per site licensing is a model that allows unlimited users within a specific location to use the software. Per core licensing is a model that charges based on the number of processor cores on the server where the software is installed. Per instance licensing is a model that charges based on the number of copies of the software running on different servers or virtual machines.

Reference:

https://www.pcmag.com/encyclopedia/term/concurrent-use-license https://www.techopedia.com/definition/1440/software-licensing

Reveal Solution Next Question

QUESTION: 114

Users cannot access a new server by name, but the server does respond to a ping request using its IP address. All the user workstations receive their IP information from a DHCP server.
Which of the following would be the best step to perform NEXT?

Run the tracert command from a workstation.
Examine the DNS to see if the new server record exists.
Correct the missing DHCP scope.
Update the workstation hosts file.

Answer(s): B

Explanation:

If users cannot access a new server by name, but the server does respond to a ping request using its IP address, it means that there is a problem with name resolution. The DNS (Domain Name System) is a service that maps hostnames to IP addresses and vice versa. Therefore, the best step to perform next is to examine the DNS to see if the new server record exists and matches its IP address. If not, the DNS record needs to be added or updated accordingly. Running the tracert command from a workstation would not help with name resolution, as it only shows the route taken by packets to reach a destination by IP address. Correcting the missing DHCP scope would not help either, as DHCP (Dynamic Host Configuration Protocol) only assigns IP addresses and other network settings to clients, but does not resolve names. Updating the workstation hosts file would be a temporary workaround, but not a permanent solution, as it would require manually editing every workstation's hosts file with the new server's name and IP address.

Reference:

https://www.howtogeek.com/164981/how-to-use-nslookup-to-check-domain-name-information-in- microsoft-windows/ https://www.howtogeek.com/howto/27350/beginner-geek-how-to-edit-your-

hosts-file/

Reveal Solution Next Question

QUESTION: 115

Which of the following techniques can be configured on a server for network redundancy?

Clustering
Vitalizing
Cloning
Teaming

Answer(s): D

Explanation:

Teaming is a technique that can be configured on a server for network redundancy. Teaming involves combining two or more network adapters into a single logical unit that acts as one network interface. This way, if one network adapter fails, another one can take over without disrupting network connectivity. Teaming can also improve network performance by load balancing traffic across multiple network adapters. Clustering is a technique that involves grouping two or more servers together to act as one system for high availability and fault tolerance. Virtualizing is a technique that involves creating multiple virtual machines on a single physical server to optimize resource utilization and flexibility. Cloning is a technique that involves creating an exact copy of a server's configuration and data for backup or migration purposes.

Reference:

https://docs.microsoft.com/en-us/windows- server/networking/technologies/nic-teaming/nic-teaming https://www.techopedia.com/definition/19588/clustering https://www.techopedia.com/definition/4790/virtualization https://www.techopedia.com/definition/4776/cloning

Reveal Solution Next Question

QUESTION: 116

An administrator is investigating a physical server mat will not Boot into the OS. The server has three hard drives configured in a RAID 5 array. The server passes POST, out the OS does not load. The administrator verities the CPU and RAM are Doth seated correctly and checks the dual power supplies. The administrator then verifies all the BIOS settings are correct and connects a bootable USB drive in the server, and the OS loads correctly.
Which of the following is causing the issue?

The page file is too small.
The CPU has failed.
There are multiple failed hard drives.
There are mismatched RAM modules.
RAID 5 requires four drives

Answer(s): C

Explanation:

If a server has three hard drives configured in a RAID 5 array, it means that the data is striped across all three drives with parity information. RAID 5 can tolerate one drive failure without losing data, but not two or more. If there are multiple failed hard drives, the RAID 5 array will become corrupted and the OS will not load. The other options are not likely to cause the issue, as the server passes POST, the CPU and RAM are seated correctly, the BIOS settings are correct, and the OS loads from a bootable USB drive. RAID 5 does not require four drives, it can work with three or more.

Reference:

https://www.technewstoday.com/what-is-a-raid-5/

Reveal Solution Next Question

Free SK0-005 Exam Braindumps (page: 29)

QUESTION: 113

Explanation:

Reference:

QUESTION: 114

Explanation:

Reference:

QUESTION: 115

Explanation:

Reference:

QUESTION: 116

Explanation:

Reference: