Free NSE5_FAZ-6.4 Exam braindumps download (NSE5_FAZ-6.4 exam dumps Free)

QUESTION: 6

Refer to the exhibit.

What does the data point at 14:55 tell you?

The received rate is almost at its maximum for this device
The sqlplugind daemon is behind in log indexing by two logs
Logs are being dropped
Raw logs are reaching FortiAnalyzer faster than they can be indexed

Answer(s): D

QUESTION: 7

You are using RAID with a FortiAnalyzer that supports software RAID, and one of the hard disks on FortiAnalyzer has failed.
What is the recommended method to replace the disk?

Shut down FortiAnalyzer and then replace the disk
Downgrade your RAID level, replace the disk, and then upgrade your RAID level
Clear all RAID alarms and replace the disk while FortiAnalyzer is still running
Perform a hot swap

Answer(s): A

Reference:

https://community.fortinet.com/t5/FortiAnalyzer/Technical-Note-How-to-swap-Hard-Disk-on- FortiAnalyzer/tap/194997?externalID=FD41397#:~:text=If%20a%20hard%20disk%20on,process%20known%20as%20 hot%20swapping

Show Answer Next Question

QUESTION: 8

On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
FortiAnalyzer is functioning normally

Answer(s): C

Reference:

https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/4cb0dce6- dbef-11e9-8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)

Show Answer Next Question

QUESTION: 9

In the FortiAnalyzer FortiView, source and destination IP addresses from FortiGate devices are not resolving to a hostname.
How can you resolve the source and destination IP addresses, without introducing any additional performance impact to FortiAnalyzer?

Resolve IP addresses on a per-ADOM basis to reduce delay on FortiView while IPs resolve
Configure # set resolve-ip enable in the system FortiView settings
Configure local DNS servers on FortiAnalyzer
Resolve IP addresses on FortiGate

Answer(s): D

Reference:

https://packetplant.com/fortigate-and-fortianalyzer-resolve-source-and-destination-ip/
“As a best practice, it is recommended to resolve IPs on the FortiGate end. This is because you get both source and destination, and it offloads the work from FortiAnalyzer. On FortiAnalyzer, this IP resolution does destination IPs only”

Show Answer Next Question

QUESTION: 10

You have recently grouped multiple FortiGate devices into a single ADOM. System Settings > Storage Info shows the quota used.
What does the disk quota refer to?

The maximum disk utilization for each device in the ADOM
The maximum disk utilization for the FortiAnalyzer model
The maximum disk utilization for the ADOM type
The maximum disk utilization for all devices in the ADOM

Answer(s): D

Show Answer Next Question

Free NSE5_FAZ-6.4 Exam Braindumps Fortinet NSE 5 - FortiAnalyzer 6.4 Questions 6–10 (page: 3)

QUESTION: 6

QUESTION: 7

Reference:

QUESTION: 8

Reference:

QUESTION: 9

Reference:

QUESTION: 10

Free NSE5_FAZ-6.4 Exam Braindumps
Fortinet NSE 5 - FortiAnalyzer 6.4 Questions 6–10 (page: 3)