Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
Splunk
ServiceNow
All Vendors
  2. Home
  3. Exams
  4. Fortinet
  5. NSE5_FAZ-7.0

Fortinet NSE5_FAZ-7.0 Exam
Fortinet NSE 5 - FortiAnalyzer 7.0 (Page 3 )

Updated On: 9-Feb-2026
Page 3 of 24
PDF with 114 Questions

Refer to the exhibit.

What does the data point at 14:55 tell you?

  1. The received rate is almost at its maximum for this device
  2. The sqlplugind daemon is behind in log indexing by two logs
  3. Logs are being dropped
  4. Raw logs are reaching FortiAnalyzer faster than they can be indexed

Answer(s): D



You are using RAID with a FortiAnalyzer that supports software RAID, and one of the hard disks on FortiAnalyzer has failed. What is the recommended method to replace the disk?

  1. Shut down FortiAnalyzer and then replace the disk
  2. Downgrade your RAID level, replace the disk, and then upgrade your RAID level
  3. Clear all RAID alarms and replace the disk while FortiAnalyzer is still running
  4. Perform a hot swap

Answer(s): A

Explanation:


Reference:

https://community.fortinet.com/t5/FortiAnalyzer/Technical-Note-How-to-swap-Hard-Disk-on-FortiAnalyzer/ta-p/194997?externalID=FD41397#:~:text=If%20a%20hard%20disk%20on,process%20known%20as%20hot%20swapping



On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

  1. FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
  2. FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
  3. FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
  4. FortiAnalyzer is functioning normally

Answer(s): C


Reference:

https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/4cb0dce6-dbef-11e9-8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)



In the FortiAnalyzer FortiView, source and destination IP addresses from FortiGate devices are not resolving to a hostname.

How can you resolve the source and destination IP addresses, without introducing any additional performance impact to FortiAnalyzer?

  1. Resolve IP addresses on a per-ADOM basis to reduce delay on FortiView while IPs resolve
  2. Configure # set resolve-ip enable in the system FortiView settings
  3. Configure local DNS servers on FortiAnalyzer
  4. Resolve IP addresses on FortiGate

Answer(s): D


Reference:

https://packetplant.com/fortigate-and-fortianalyzer-resolve-source-and-destination-ip/

“As a best practice, it is recommended to resolve IPs on the FortiGate end. This is because you get both source and destination, and it offloads the work from FortiAnalyzer. On FortiAnalyzer, this IP resolution does destination IPs only”



You have recently grouped multiple FortiGate devices into a single ADOM. System Settings > Storage Info shows the quota used. What does the disk quota refer to?

  1. The maximum disk utilization for each device in the ADOM
  2. The maximum disk utilization for the FortiAnalyzer model
  3. The maximum disk utilization for the ADOM type
  4. The maximum disk utilization for all devices in the ADOM

Answer(s): D






Post your Comments and Discuss Fortinet NSE5_FAZ-7.0 exam prep with other Community members:

Join the NSE5_FAZ-7.0 Discussion