In EVPN, Type 5 routes are used only by hosts on a VXLAN network to access external networks.
Answer(s): B
EVPN (Ethernet VPN) is a control plane technology used with VXLAN to provide Layer 2 and Layer 3 services in data center networks, including Huawei's implementations. EVPN routes are categorized into types, with Type 5 routes (IP Prefix routes) serving a specific purpose:Type 5 Routes: These routes advertise IP prefixes and are used for inter-subnet routing, allowing communication between different VXLAN Virtual Network Identifiers (VNIs) or between VXLAN networks and external networks. They carry a Layer 3 VNI and IP prefix information, enabling routers or gateways to perform Layer 3 forwarding.Usage Scope: Type 5 routes are not limited to hosts on a VXLAN network accessing external networks. They are also used by network devices (e.g., gateways, routers) within the EVPN domain to facilitate routing between subnets, including intra-VXLAN communication. For example, a centralized gateway or distributed gateway can use Type 5 routes to route traffic within the data center or to external networks, not just host-initiated access.The statement is FALSE (B) because Type 5 routes are not exclusively for hosts on a VXLAN network to access external networks; they support broader Layer 3 routing functions across the EVPN domain.
Huawei HCIP-Data Center Network Training EVPN Routing; CloudFabric EVPN Configuration Guide.
Which of the following statements is false about centralized gateway deployment using BGP EVPN?
Answer(s): D
Centralized gateway deployment using BGP EVPN in Huawei's data center networks (e.g., CloudFabric) involves a gateway handling Layer 3 routing for VXLAN overlays. Let's evaluate each statement:A . When configuring a VTEP, you need to create a Layer 2 BD and bind a VNI to the Layer 2 BD: A Bridge Domain (BD) is a Layer 2 broadcast domain in VXLAN, and a Virtual Network Identifier (VNI) is bound to it to segment traffic. This is a standard step when configuring a VXLAN Tunnel Endpoint (VTEP) to map the overlay network. TRUE.B . A VXLAN tunnel is identified by a pair of VTEP IP addresses and can be established if the local and remote VTEP IP addresses are reachable to each other at Layer 3: VXLAN tunnels are established between VTEPs using their IP addresses as endpoints. Layer 3 reachability (e.g., via underlay routing) is required for tunnel establishment. TRUE.C . When BGP EVPN is used to dynamically establish a VXLAN tunnel, the local and remote VTEPs first establish a BGP EVPN peer relationship and then exchange BGP EVPN routes to transmit VNI and VTEP IP address information. A VXLAN tunnel is then dynamically established between them: In BGP EVPN, VTEPs establish a BGP peer relationship, exchange routes (e.g., Type 2 for MAC/IP or Type 3 for multicast), and share VNI and VTEP IP details, enabling dynamic tunnel setup. TRUE.D . When configuring a VTEP, you need to create an EVPN Instance in the Layer 2 BD and configure an RD for the local EVPN instance. You do not need to configure an RT: An EVPN Instance (EVI) is created within a BD, and a Route Distinguisher (RD) is configured to make routes unique. However, RouteTargets (RTs) are also required to control route import/export between EVPN peers, ensuring proper VNI and route distribution. Stating that RT configuration is not needed is incorrect, as RTs are essential for BGP EVPN operation. FALSE.Thus, D is the false statement because RT configuration is necessary in centralized gateway deployment with BGP EVPN.
Huawei CloudFabric Data Center Network Solution BGP EVPN Configuration; HCIP-Data Center Network Training EVPN Gateway Deployment.
In network overlay, both endpoints of a VXLAN tunnel are physical switches.
In a network overlay, VXLAN (Virtual Extensible LAN) tunnels extend Layer 2 networks over a Layer 3 underlay, commonly implemented in Huawei's data center solutions. The endpoints of a VXLAN tunnel are VXLAN Tunnel Endpoints (VTEPs), which encapsulate and decapsulate traffic.VTEP Roles: VTEPs can be physical switches (e.g., Huawei CloudEngine series), virtual switches (e.g., Open vSwitch on a hypervisor), or routers with VXLAN support. The endpoints are defined by their IP addresses, not their physical nature.Deployment Flexibility: In modern data centers, VXLAN tunnels often connect physical switches to virtualized environments where VTEPs reside on hypervisors or servers hosting VMs. For example, a VM's vNIC might connect to a virtual switch (VTEP) that tunnels to a physical switch VTEP. Thus, both endpoints are not always physical switches; one or both can be virtual.The statement is FALSE (B) because both endpoints of a VXLAN tunnel are not necessarily physical switches; they can include virtual VTEPs in hypervisors or other devices.
Huawei HCIP-Data Center Network Training VXLAN Overlay; CloudFabric VXLAN Deployment Guide.
To allow access to a VXLAN network, you need to configure service access points on devices. There are two access modes: Layer ? sub-interface and binding. (Enter the acronym in uppercase letters.)
Answer(s): A
VXLAN (Virtual Extensible LAN) is a network overlay technology that extends Layer 2 networks over a Layer 3 underlay, commonly implemented in Huawei's CloudFabric data center solutions. To enable access to a VXLAN network, service access points (e.g., interfaces or sub-interfaces) must be configured on devices such as switches or routers acting as VXLAN Tunnel Endpoints (VTEPs). The question mentions two access modes: "Layer ? sub-interface" and "binding," with the task to fill in the layer acronym in uppercase letters.Context Analysis: The missing layer is indicated by a "?" and is part of a sub-interface configuration. In networking, sub-interfaces are typically associated with Layer 3 (e.g., for VLAN tagging or VXLAN integration), where they handle IP routing or mapping to overlay networks.Access Modes:Layer 3 Sub-Interface: This mode involves configuring a sub-interface on a Layer 3 device (e.g., a router or Layer 3 switch) to terminate VXLAN tunnels and perform routing. The sub-interface is associated with a VNI (VXLAN Network Identifier) and often uses a Layer 3 protocol (e.g., BGP EVPN) to connect to the VXLAN overlay.Binding: This likely refers to binding a VNI to a Bridge Domain (BD) or interface, a common practice in Huawei's VXLAN configuration to map the overlay network to a physical or logical port. This can occur at Layer 2 or Layer 3, but the sub-interface context suggests Layer 3 involvement.The question's structure implies the layer number for the sub-interface mode, which is Layer 3 in VXLAN contexts for routing and gateway functions. Thus, the acronym (digit) to enter is 3.
Huawei CloudFabric Data Center Network Solution VXLAN Configuration Guide; HCIP- Data Center Network Training VXLAN Access Methods.
A VXLAN tunnel is identified by a pair of VTEP IP addresses. During VXLAN tunnel establishment, the local and remote VTEPs attempt to obtain each other's IP addresses. If the VTEP IP addresses are reachable to each other at Layer 3, a VXLAN tunnel can be established.
VXLAN (Virtual Extensible LAN) tunnels are used to encapsulate Layer 2 traffic over a Layer 3network, a key feature in Huawei's data center solutions. The endpoints of a VXLAN tunnel are VXLAN Tunnel Endpoints (VTEPs), identified by their IP addresses.Tunnel Identification: A VXLAN tunnel is uniquely identified by the pair of VTEP IP addresses (local and remote), along with the VNI (VXLAN Network Identifier). This pair ensures the tunnel is specific to the communication path between the two VTEPs.Tunnel Establishment: During setup, VTEPs exchange information to learn each other's IP addresses. This can occur manually (static configuration) or dynamically (e.g., via BGP EVPN). The underlay network must provide Layer 3 reachability between the VTEP IP addresses, typically using routing protocols (e.g., OSPF, BGP) to ensure IP connectivity.Reachability Condition: If the local and remote VTEP IP addresses are reachable at Layer 3, the tunnel can be established, allowing encapsulation and decapsulation of VXLAN traffic. This is a fundamental requirement in Huawei's VXLAN implementation.The statement is TRUE (A) because a VXLAN tunnel's identification and establishment depend on reachable VTEP IP address pairs at Layer 3.
Huawei HCIP-Data Center Network Training VXLAN Tunneling; CloudFabric VXLAN Deployment Guide.
Post your Comments and Discuss Huawei H12-893_V1.0 exam prep with other Community members:
Our website is free, but we have to fight against AI bots and content theft. We're sorry for the inconvenience caused by these security measures. You can access the rest of the H12-893_V1.0 content, but please register or login to continue.