JN0-481 Practice Test & Exam Dumps
Data Center, Specialist (JNCIS-DC) Questions 21–25 (page: 6)

Updated On: 23-Feb-2026

You are creating a new security policy using Juniper Apstra.



Referring to the exhibit, which application point should you select to allow or deny traffic to or from a particular VRF?

  1. Routing Zone
  2. External Endpoint
  3. Internal Endpoint
  4. Virtual Network

Answer(s): A

Explanation:

In Apstra 5.1, multitenancy is modeled using routing zones, which map directly to the network operating system concept of a VRF. A VRF is an isolated Layer 3 routing instance with its own routing table and forwarding context, and Apstra's routing zone is the intent-based abstraction used to define and manage that isolation consistently across the fabric. Therefore, if your goal is to allow or deny traffic to or from a particular VRF, you must select Routing Zone as the security policy application point.

This choice enables you to express policy at the tenant boundary (VRF boundary) rather than at a single segment boundary. In EVPN-VXLAN data center fabrics, a tenant VRF commonly contains multiple virtual networks (VXLAN segments) and their associated IRB gateways on the leaf switches. Applying policy at the routing-zone level allows Apstra to compile intent and deploy enforcement consistently where traffic enters or exits that VRF context--typically as ACL constructs rendered as Junos firewall filters on the appropriate interfaces (for example, IRB interfaces for east-west controls or border interfaces for north-south controls).

By contrast, selecting Virtual Network targets a single segment (not the whole VRF), and Internal/External Endpoint targets specific endpoints or endpoint groups rather than the VRF-wide policy boundary. Hence, Routing Zone is the correct application point when policy scope is the VRF.



You are performing an upgrade to your switches in your network. You want to ensure that the upgrade can be performed without interrupting traffic. In the Juniper Apstra UI, which deploy mode should be used to accomplish this task?

  1. Deploy
  2. Undeploy
  3. Drain
  4. Ready

Answer(s): C

Explanation:

In Apstra, Deploy Mode = Drain is the operational mechanism used to gracefully remove a switch from active forwarding before performing maintenance such as an OS upgrade. Drain mode is specifically intended to drain traffic while preserving fabric stability, so that maintenance can be executed with minimal to no application impact, provided the fabric design has sufficient redundancy (for example, ECMP in the underlay and dual-homing/ESI for server attachments). In an EVPN-VXLAN IP fabric, taking a leaf or spine abruptly out of service can cause transient loss of reachability as underlay adjacencies reconverge and the overlay recalculates paths. By placing the device into Drain, Apstra adjusts intent so that traffic is shifted away from the device as much as possible, reducing dependency on it before the upgrade begins.

This is different from Undeploy, which removes Apstra-rendered configuration and is generally used for decommissioning; if a device is carrying traffic, Apstra guidance is to drain first. Ready is a pre- deploy state used in lifecycle workflows, not a maintenance traffic-shifting mode. Deploy keeps the device fully participating. Therefore, for a maintenance window where the goal is "upgrade with minimal interruption," the correct mode is Drain, then perform the Junos v24.4 upgrade, and finally return the device to Deploy.

Verified Juniper sources (URLs):

https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-drain-mode/apstra-drain- mode.pdf https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-user-guide/topics/topic- map/deploy-mode-update-datacenter.html https://www.juniper.net/documentation/us/en/software/apstra6.0/apstra-user-guide/topics/topic- map/device-config-lifecycle.html



When creating a probe, an operator wants to make it easy to view that probe's output. In this scenario, which element must be created to accomplish this task?

  1. A dashboard widget
  2. A predefined probe
  3. A processor
  4. A stage

Answer(s): A

Explanation:

In Apstra IBA, a probe is a directed graph made of stages (data you can inspect) and processors (operations that transform/aggregate data).
While stages can be inspected during probe construction, the simplest operational way to make probe results readily consumable by day-2 operators is to publish them through widgets that can be placed on Analytics dashboards. A dashboard widget is the visualization and presentation object that renders either (1) counts of anomalies or (2) the outputs produced by stages and processors in a probe. Creating a widget tied to the probe output means the operator can open a dashboard and immediately see the metric trends, tables, or anomaly indicators without navigating into probe internals.

A predefined probe is optional content (a starting template) and is not required for visibility. Processors and stages are internal probe building blocks, but they do not, by themselves, create an operator-friendly view in the UI. In a Junos v24.4 EVPN-VXLAN fabric, this is especially useful for link utilization, drops, latency signals, or any custom telemetry pipeline: you build the probe logic once, then expose the key results in a widget that persists across operational workflows and can be shared on standardized dashboards for capacity planning and troubleshooting.

Verified Juniper sources (URLs):

https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-user- guide/topics/concept/widgets.html https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-user-guide/topics/topic- map/widget-stage-create.html https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-user- guide/topics/concept/probes.html



Juniper Apstra provides five different predefined user roles. Given this information, what is the main difference between the administrator and the user role?

  1. The user role can only be assigned to specific blueprints.
  2. The user role can make changes to any other role.
  3. The user role cannot make any changes to other user types.
  4. The user role can only make changes to the view role.

Answer(s): C

Explanation:

Apstra role-based access control separates fabric operations from identity and authorization administration. The administrator role includes full permissions, including the ability to manage users and roles (for example, creating users, assigning permissions, and creating/cloning/editing custom roles where allowed). This enables administrators to govern who can access the system and what they are permitted to change across all blueprints and system settings.

The user role, in contrast, is designed for day-to-day fabric work: viewing and editing supported blueprint elements and operational objects within the scope permitted by the role, but not administering other users' access or modifying the role structure itself. In other words, a user can work on the network intent and operations, but cannot elevate privileges, change other users' roles, or otherwise manage user/role administration unless explicitly granted additional permissions through custom roles.

That makes option C the correct statement: the user role cannot make changes to other user types (that is, it lacks the permissions needed to administer identities/roles). Options A, B, and D do not reflect Apstra's RBAC model: roles are not primarily constrained "per blueprint" in that way, and users are not intended to modify other roles--those are administrator-level capabilities.

Verified Juniper sources (URLs):

https://www.juniper.net/documentation/us/en/software/apstra6.0/apstra-user- guide/topics/concept/user-role-management.html https://www.juniper.net/documentation/us/en/software/apstra4.2/apstra-user- guide/topics/concept/user-role-management.html https://www.juniper.net/documentation/us/en/software/apstra5.0/apstra-user- guide/topics/concept/user-role-management.html



Which statement is correct about an event log?

  1. It stores alerts for anomalies in the event log.
  2. It can be exported to a PDF file.
  3. You can view the configuration of a device.
  4. It runs on the worker node.

Answer(s): A

Explanation:

In Juniper Apstra 5.1, the Event Log is a centralized record used for auditing and operational visibility. It includes audit events (user/system actions) and anomaly-related alerts (events generated when Apstra detects abnormal conditions). In Apstra documentation, anomaly entries are explicitly treated as "Alert" records with high severity, meaning the Event Log is a valid place to review anomaly notifications and their associated details. Therefore, the statement that the Event Log stores alerts for anomalies is correct.

The other options do not match the Event Log function. Viewing a device's configuration is handled in device configuration and blueprint operational views, not as the primary purpose of the Event Log. Export behavior, where supported, is described for formats such as CSV rather than PDF, and exporting dashboards is a separate capability from event logging. Finally, while worker nodes are used to offload operational services (such as off-box agents and IBA components), the Event Log is a platform logging feature exposed through the controller UI/API rather than something described as "running on the worker node" as its defining trait.

Verified Juniper sources (URLs):

https://www.juniper.net/documentation/us/en/software/apstra5.1/apstra-user-guide/topics/topic- map/event-log.html https://www.juniper.net/documentation/us/en/software/apstra5.0/apstra-user-guide/topics/topic- map/event-log.html https://www.juniper.net/documentation/us/en/software/apstra5.1/apstra-user-guide/topics/topic- map/syslog-config.html



Viewing page 6 of 14
Viewing questions 26 - 30 out of 65 questions


Post your Comments and Discuss Juniper JN0-481 exam prep with other Community members:

AI Tutor AI Tutor 👋 I’m here to help!