QUESTION: 49

An administrator needs to create a new Linux image and will to do the following as part of the VM deployment:

* Set the OS hostname

* Add custom users

* Add keys

* Run custom scripts

What package needs to be installed in the Linux image to facilitate this automation?

CloudInit
Sysprep
Kickstart
NGT

Answer(s): A

Explanation:

CloudInit is a package that contains utilities for early initialization of cloud instances. It allows you to customize virtual machines provided by a cloud vendor by modifying the generic OS configuration on boot. You can use CloudInit to set the OS hostname, add custom users, add keys, run custom scripts, and more2. CloudInit is supported by most major Linux and FreeBSD operating systems and works across different cloud platforms3. Sysprep is a tool for Windows operating systems that prepares an installation for cloning, auditing, and customer delivery4.

Reference:

1: Replacing Nodes in Nutanix Cluster - Nutanix Support & Insights 2: Customize a Linux VM with cloud-init in Azure - Azure Virtual Machines 3: Cloud-Init - The standard for customising cloud instances 4: Sysprep (Generalize) a Windows installation

Reveal Solution Next Question

QUESTION: 50

An administrator has created a Nutanix managed it a VLAN ID of 512.

Several VMs have been created, and the administrator notices that the can successfully communicate with other VMs on that VLAN.

Provided they are on the host, but cannot communicate with VMs that reside on different hosts in the cluster.

What is most likely thee cause of this issue?

There is a firewall rule blockingVLAN512 traffic.
VLANS12 is a reserved VLAN ID, and not usable for guest VMs.
The VLAN was not created on the upstream switches.
The administrator did not create the VLAN on all hosts

Answer(s): C

Explanation:

The correct answer is C. The VLAN was not created on the upstream switches.

A VLAN (virtual local area network) is a logical segmentation of a physical network that allows devices on the same VLAN to communicate with each other, regardless of their physical location. A VLAN also isolates the devices on different VLANs from each other, unless there is a router or a layer

3 switch that can route traffic between VLANs. To create a VLAN, the administrator needs to configure the network devices that are involved in the VLAN, such as switches, routers, and hosts. The administrator also needs to assign a unique VLAN ID to each VLAN, which is a number between 1 and 4094 that identifies the VLAN1.

In Nutanix AHV, the administrator can create a Nutanix managed network with a specific VLAN ID for guest VMs. This network can be assigned to VM NICs using Prism Element or Prism Central. However, creating a Nutanix managed network does not automatically create the VLAN on the upstream switches that connect the AHV hosts. The administrator needs to manually configure the upstream switches to allow the VLAN traffic on the ports that connect to the AHV hosts. The administrator also needs to ensure that the upstream switches are interconnected physically or virtually and can forward traffic between different VLANs if needed2.

Therefore, if an administrator has created a Nutanix managed network with a VLAN ID of 512 and notices that the VMs on that network can only communicate with other VMs on the same host, but not with VMs on different hosts in the cluster, the most likely cause of this issue is that the VLAN was not created on the upstream switches. This means that the switches are dropping or blocking the traffic with VLAN ID 512 and preventing it from reaching other hosts or VMs. To resolve this issue, the administrator should create the VLAN on the upstream switches and allow it on the ports that connect to the AHV hosts3.

Reference:

Nutanix AHV Networking Best Practices

Reveal Solution Next Question

QUESTION: 51

An administrator is concerned about the amount of data that a VM reading and writing to the storage fabric.

Which metric will provide that data?

Host Hypervisor IO Bandwidth
Host Disk IOPS
VM Storage Controller IOPS
VM Storage Controller Bandwidth

Answer(s): D

Explanation:

The correct answer is D. VM Storage Controller Bandwidth.

VM Storage Controller Bandwidth is a metric that measures the amount of data that a VM is reading and writing to the storage fabric. The storage fabric is the network of storage controllers (CVMs) that provide distributed and fault-tolerant storage services to the VMs on the Nutanix cluster. The VM Storage Controller Bandwidth metric shows the read and write bandwidth in megabytes per second (MBps) for each VM. The higher the bandwidth, the more data the VM is transferring to and from the storage fabric1.

The administrator can use Prism Central to view the VM Storage Controller Bandwidth metric for each VM in a chart or a widget. The administrator can also use Prism Central to view other metrics related to the VM's storage performance, such as VM Storage Controller IOPS, VM Storage Controller Latency, and VM Disk Usage2.

Reference:

Nutanix Metrics

Reveal Solution Next Question

QUESTION: 52

Refer to the Exhibit:

An administrator receives complaints of poor performance in a particular VM.

Based on the VM performance metric, what is the most likely cause of this behavior?

Oplog is full cannot serve IO request from this VM.
The host's CPU is severely overloaded.
SSD tier is not big enough to serve workloads' IOPS demand.
The VM needs more vCPUs

Answer(s): B

Explanation:

Based on the VM performance metrics shown in the exhibit, the most likely cause of the poor performance in the particular VM is that the host's CPU is severely overloaded. This is indicated by the high percentage of Hypervisor CPU Ready Time, which is shown as 96% in the CPU ready chart. CPU Ready Time is a metric that shows the amount of time a VM is ready to run but is unable to run because the host CPU resources are not available. In a healthy environment, this value is typically low. A high percentage indicates that the VMs are waiting for available CPU cycles, which means the CPU is not able to schedule the VM effectively, often due to overcommitment or heavy CPU load.

When the CPU ready time is consistently high, it is a clear indicator that the VM is frequently waiting for CPU resources, which can lead to performance issues such as sluggishness or delays in processing. It is not related to the storage subsystem (Oplog fullness or SSD tier size), nor directly to the number of vCPUs assigned to the VM.
While adding more vCPUs might seem like a solution, it could actually exacerbate the issue if the host is already CPU constrained.

To resolve this issue, an administrator should consider balancing the load across the hosts more effectively, possibly by using Nutanix's built-in automation and balancing features, or by scaling out the cluster to add more CPU resources. It is also advisable to check for any VMs with unusually high CPU demand and to adjust resource allocation as needed. Nutanix provides extensive documentation and guidelines in their Resource Management Guide to help administrators identify and resolve such performance issues.

Reveal Solution Next Question

Free NCP-MCI Exam Braindumps (page: 13)

QUESTION: 49

Explanation:

Reference:

QUESTION: 50

Explanation:

Reference:

QUESTION: 51

Explanation:

Reference:

QUESTION: 52

Explanation: