support@Free-Braindumps.com
Register Login
Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
CrowdStrike
Anthropic
All Vendors
  1. Home
  2. Exams
  3. Cisco
  4. 200-301

Free 200-301 Exam Braindumps
Cisco Certified Network Associate (CCNA) Questions 536–540 (page: 109)

Updated On: 10-Feb-2026
Page 109 of 281
PDF with 1395 Questions

What is the primary purpose of a First Hop Redundancy Protocol?

  1. It allows directly connected neighbors to share configuration information
  2. It reduces routing failures by allowing Layer 3 load balancing between OSPF neighbors that have the same link metric
  3. It allows a router to use bridge priorities to create multiple loop-free paths to a single destination
  4. It reduces routing failures by allowing more than one router to represent itself as the default gateway of a network

Answer(s): D



An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

  1. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.255 ip nat outside destination list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  2. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.254 ip nat inside source list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  3. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 route map permit 10.10.0.0 255.255.255.0 ip nat outside destination list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside
  4. enable configure terminal ip nat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30 access-list 1 permit 10.10.0.0 0.0.0.255 ip nat inside source list 1 pool mypool interface g1/1 ip nat inside interface g1/2 ip nat outside

Answer(s): D



When the active router in an HSRP group fails, which router assumes the role and forwards packets?

  1. forwarding
  2. listening
  3. standby
  4. backup

Answer(s): C



What protocol allows an engineer to back up 20 network router configurations globally while using the copy function?

  1. TCP
  2. SMTP
  3. FTP
  4. SNMP

Answer(s): C



Which type of address is the public IP address of a NAT device?

  1. outside global
  2. outside local
  3. inside global
  4. inside local
  5. outside public
  6. inside public

Answer(s): C

Explanation:

NAT use four types of addresses:
-Inside local address - The IP address assigned to a host on the inside network. The address is usually not an IP address assigned by the Internet Network Information Center (InterNIC) or service provider. This address is likely to be an RFC 1918 private address.
-Inside global address - A legitimate IP address assigned by the InterNIC or service provider that represents one or more inside local IP addresses to the outside world.
-Outside local address - The IP address of an outside host as it is known to the hosts on the inside network.
-Outside global address - The IP address assigned to a host on the outside network. The owner of the host assigns this address.
-



  PDF
Viewing page 109 of 281
Viewing questions 541 - 545 out of 1395 questions


Post your Comments and Discuss Cisco 200-301 exam prep with other Community members:

AI Tutor AI Tutor 👋 I’m here to help!