CompTIA
Checkpoint
ISC
HP
Dell
EC-Council
EXIN
Fortinet
ITIL®
Juniper
PMI
Microsoft
VMware
Avaya
Google
Salesforce
Amazon
Palo Alto Networks
Certiport
ISC2
All Vendors
  2. Home
  3. Exams
  4. Cisco®
  5. 300-410

Free 300-410 Exam Braindumps (page: 70)

Page 70 of 156
PDF with 620 Questions

Refer to the exhibit. An engineer must configure DMVPN Phase 3 hub-and-spoke topology to enable a spoke-to-spoke tunnel. Which NHRP configuration meets the requirement on R6?

  1. interface Tunnel1
    ip nhrp authentication Cisco123
    ip nhrp map multicast dynamic
    ip nhrp network-id 1
    ip nhrp holdtime 300
    ip nhrp redirect
  2. interface Tunnel 1
    ip address 192.168.1.1 255.255.255.0
    tunnel source e 0/1
    tunnel mode gre multipoint
    ip nhrp network-id 1
    ip nhrp map 192.168.1.2 192.1.20.2
  3. interface Tunnel1
    ip nhrp authentication Cisco123
    ip nhrp map multicast dynamic
    ip nhrp network-id 1
    ip nhrp holdtime 300
    ip nhrp shortcut
  4. Interface Tunnel 1
    ip address 192.168.1.1 255.255.255.0
    tunnel source e 0/0
    tunnel mode gre multipoint
    ip nhrp network-id 1

Answer(s): A



Refer to the exhibit. An engineer implemented CoPP but did not see OSPF traffic going through it. Which configuration resolves the issue?

  1. control-plane
    service-policy input COPP
  2. policy-map COPP class OSFP
    police 8000 conform-action transmit exceed-action transmit violate-action drop
  3. ip access-list extended OSFP
    permit ospf any any
  4. class-map match-all OSFP
    match access-group name OSFP

Answer(s): C



Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?



  1. Site3
    router eigrp 100
    variance 2
  2. Site2
    router eigrp 100
    variance 2
  3. Site2
    router eigrp 100
    variance 3
  4. Site1
    router eigrp 100
    variance 3

Answer(s): D



Refer to the exhibit. R1 and R2 use IGP protocol to route traffic between AS 100 and AS 200 despite being configured to use BGP. Which action resolves the issue and ensures the use of BGP?

  1. Configure distance to 100 under the OSPF process of R1 and R2
  2. Remove distance commands under BGP AS 100
  3. Remove distance commands under BGP AS 100 and AS 200.
  4. Configure distance to 100 under the EIGRP process of R1 and R2

Answer(s): C



Page 70 of 156



Post your Comments and Discuss Cisco® 300-410 exam with other Community members:

Ramu commented on February 24, 2024
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
Anonymous
upvote

Loren commented on August 06, 2021
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
UNITED STATES
upvote

Asaya commented on August 04, 2021
It is looking good. I just made my download. Study begins tomorrow.
BRAZIL
upvote

Kalib commented on April 12, 2021
With my busy schedule this is the best source of studying to pass my exam.
AUSTRALIA
upvote