Which SNMPv3 configuration must be used to support the strongest security possible?
Answer(s): D
Refer to the exhibit.Which command was used to generate this output and to show which ports are authenticating with dot1x or mab?
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/s1/sec-s1-xe-3se-3850-cr-book/sec-s1- xe-3se-3850-cr-book_chapter_01.html#wp3404908137Displaying the Summary of All Auth Manager Sessions on the Switch Enter the following:Switch# show authentication sessionsInterface MAC Address Method Domain Status Session ID Gi1/48 0015.63b0.f676 dot1x DATA Authz Success 0A3462B1000000102983C05C Gi1/5 000f.23c4.a401 mab DATA Authz Success 0A3462B10000000D24F80B58 Gi1/5 0014.bf5d.d26d dot1x DATA Authz Success 0A3462B10000000E29811B94
What Cisco command shows you the status of an 802.1X connection on interface gi0/1?
Answer(s): B
Refer to the exhibit.What does the number 15 represent in this configuration?
The syntax of this command is shown below:snmp-server group [group-name {v1 | v2c | v3 [auth | noauth | priv]}] [read read-view] [write write- view] [notify notify-view] [access access-list]The command above restricts which IP source addresses are allowed to access SNMP functions on the router. You could restrict SNMP access by simply applying an interface ACL to block incoming SNMP packets that don't come from trusted servers. However, this would not be as effective as using the global SNMP commands shown in this recipe. Because you can apply this method once for the whole router, it is much simpler than applying ACLs to block SNMP on all interfaces separately. Also, using interface ACLs would block not only SNMP packets intended for this router, but also may stop SNMP packets that just happened to be passing through on their way to some other destination device.
Under which two circumstances is a CoA issued? (Choose two)
Answer(s): B,D
The profiling service issues the change of authorization in the following cases: Endpoint deleted--When an endpoint is deleted from the Endpoints page and the endpoint is disconnected or removed from the network.An exception action is configured--If you have an exception action configured per profile that leads to an unusual or an unacceptable event from that endpoint. The profiling service moves the endpoint to the corresponding static profile by issuing a CoA. An endpoint is profiled for the first time--When an endpoint is not statically assigned and profiled for the first time; for example, the profile changes from an unknown to a known profile. + An endpoint identity group has changed--When an endpoint is added or removed from an endpoint identity group that is used by an authorization policy. The profiling service issues a CoA when there is any change in an endpoint identity group, and the endpoint identity group is used in the authorization policy for the following:++ The endpoint identity group changes for endpoints when they are dynamically profiled ++ The endpoint identity group changes when the static assignment flag is set to true for a dynamic endpoint An endpoint profiling policy has changed and the policy is used in an authorization policy--When an endpoint profiling policy changes, and the policy is included in a logical profile that is used in an authorization policy. The endpoint profiling policy may change due to the profiling policy match or when an endpoint is statically assigned to an endpoint profiling policy, which is associated to a logical profile. In both the cases, the profiling service issues a CoA, only when the endpoint profiling policy is used in an authorization policy.
https://www.cisco.com/c/en/us/td/docs/security/ise/2- 1/admin_guide/b_ise_admin_guide_21/b_ise_admin_guide_20_chapter_010100.html
Post your Comments and Discuss Cisco 350-701 exam dumps with other Community members:
Casper Commented on March 02, 2026 q219 and q 220 the same Anonymous
Mikser Commented on February 27, 2026 Question 26 and 36 are not correct shows Anonymous
saira Commented on September 05, 2025 great quality Anonymous
DEVENDRA Commented on September 04, 2025 HOW CAN I USE Simulator software (.EXM) FOR pRACTICE UNITED STATES
sac Commented on August 07, 2025 reveiew q 36 UNITED STATES
Sasco Commented on July 31, 2025 This site is accurate UNITED STATES
Phany Commented on July 07, 2025 A network engineer is configuring DMVPN and entered the crypto isakmp key cisc0380739941 address 0.0.0.0 command on host Should be the same on hostB POLAND
Phany Commented on July 07, 2025 Really usefull POLAND
Anonymous Commented on May 12, 2025 Q130 the correct answer is aaa new-model. This command enable AAA UNITED STATES
David A Commented on January 16, 2024 Good Colombia Anonymous
Kim Commented on May 25, 2023 I just purchased and downloaded my files. Everything looks good so far. UNITED STATES