QUESTION: 5

DRAG DROP (Drag and Drop is not supported)
A platform engineer is creating a Dell PowerScale cluster using the Configuration Wizard. They have selected the Create a new cluster option.
What Is the correct sequence of steps to create the cluster?

See Explanation section for answer.

Answer(s): A

Explanation:

The correct sequence is:
Accept End User License Agreement
Configure cluster name
Configure cluster join mode
Configure internal network
Configure external network

When creating a new Dell PowerScale cluster using the Configuration Wizard, the steps must be performed in a specific sequence to ensure proper setup and functionality. Below is the detailed order of the steps with explanations and references to Dell PowerScale documentation.

1. Accept End User License Agreement
Purpose:
Before any configuration can begin, you must accept the End User License Agreement (EULA) to comply with legal requirements and proceed with the cluster setup.
Action:
Review the EULA presented in the Configuration Wizard.

Select the option to accept the terms and conditions.
Dell PowerScale Reference
Dell EMC PowerScale OneFS Installation Guide
Chapter: Initial Configuration
The Configuration Wizard begins by displaying the EULA, which must be accepted to continue.
Best Practices:
Carefully read the EULA to understand your rights and obligations.

2. Configure Cluster Name
Purpose:
Assigning a cluster name is essential for identification and management purposes within your network environment.

Action:
Enter a unique and descriptive name for the cluster when prompted.
Dell PowerScale Reference
Dell EMC PowerScale OneFS Installation Guide
Section: Configuring Cluster Settings
After accepting the EULA, the wizard prompts for cluster-specific settings, starting with the cluster name.
Best Practices:
Use a naming convention that aligns with your organization's standards. Ensure the cluster name is DNS-resolvable if necessary.

3. Configure Cluster Join Mode
Purpose:
Determine whether to create a new cluster or join an existing one. Since you are creating a new cluster, you need to select the appropriate join mode.
Action:
Choose "Create a new cluster" from the available options.
Dell PowerScale Reference
Dell EMC PowerScale OneFS Installation Guide
Section: Cluster Creation Options
The wizard asks whether to create a new cluster or join an existing one.
Best Practices:
Verify that all nodes intended for the cluster are correctly cabled and powered on.

4. Configure Internal Network
Purpose:
Set up the internal networking (back-end network) that enables communication between nodes within the cluster.
Critical for cluster operations, data replication, and management traffic.
Action:
Configure settings for internal interfaces int-a and int-b.
Assign IP address ranges and netmasks as required.
Dell PowerScale Reference
Dell EMC PowerScale Networking Configuration Guide
Chapter: Configuring Internal Networks
Details on setting up the internal network interfaces during cluster creation.
Best Practices:
Use separate subnets for int-a and int-b to enhance redundancy. Ensure that the internal network is isolated from external networks for security.

5. Configure External Network
Purpose:
Establish the external networking (front-end network) that allows clients and services to access the cluster.
Action:
Configure settings for external network interfaces.
Assign IP addresses, netmasks, gateways, and DNS information.
Dell PowerScale Reference
Dell EMC PowerScale Networking Configuration Guide
Chapter: Configuring External Networks
Provides guidance on setting up external interfaces after internal networking is configured.
Best Practices:
Plan IP addressing to avoid conflicts within your network. Configure SmartConnect zones if required for load balancing and failover.

Additional Notes:
Sequence Importance:
Following this sequence ensures that foundational settings are established before dependent configurations.
For example, internal networking must be configured before external networking to ensure proper node communication.
Validation and Testing:
After completing the Configuration Wizard, validate the cluster setup by checking node status and network connectivity.
Use the OneFS web administration interface or CLI commands to verify configurations.
Reference to Dell PowerScale Documentation:
Dell EMC PowerScale OneFS Installation Guide
Provides step-by-step instructions for initial cluster setup.
Dell EMC PowerScale Networking Configuration Guide
Offers detailed information on networking configurations and best practices.
Dell EMC PowerScale OneFS Administration Guide
Useful for advanced configurations and cluster management post-installation.

Conclusion:
By following the sequence outlined above, the platform engineer can successfully create a new Dell PowerScale cluster using the Configuration Wizard. Each step builds upon the previous one, ensuring a robust and properly configured cluster ready for operation.

Reveal Solution Next Question

QUESTION: 6

A platform engineer must replace a failed chassis on a Dell PowerScale Gen6 cluster.
What must the engineer do after powering off the nodes?

Remove the drive sleds, label them for identification, and place the drive sleds In the newly installed chassis.
Remove the drive sleds and motherboard and transfer them to the new chassis.
Remove the drives and compute modules and reimage each drive before installing them in the chassis.
Remove the drives, install the chassis, and place the drives in the new chassis.

Answer(s): A

Explanation:

When replacing a failed chassis in a Dell PowerScale Gen6 cluster, it's critical to preserve the data and configuration by maintaining the exact placement of the drive sleds. After powering off the nodes, the engineer should:
Remove Drive Sleds:

Carefully remove each drive sled from the failed chassis.
Label for Identification:
Label each drive sled with its corresponding slot number or unique identifier.
Install New Chassis:
Mount the new chassis in the rack where the failed one was located.
Reinstall Drive Sleds:
Insert the labeled drive sleds into the same slots in the new chassis.
Power On Nodes:
Power on the nodes and verify that they boot correctly and rejoin the cluster. This procedure ensures that the drives remain in their original configuration, preserving data integrity and cluster settings. There's no need to transfer motherboards or reimage drives, as these actions could disrupt cluster operations and lead to data loss.

Reference:

Dell PowerScale Hardware Replacement Guide Chassis Replacement Procedures Dell PowerScale OneFS Administration Guide Best Practices for Hardware Maintenance Dell Knowledge Base Article Preserving Drive Order During Chassis Replacement

Reveal Solution Next Question

QUESTION: 7

Dell Technical Support has requested a part be sent back to Dell Logistics to be studied.
Which process or document musi be completed before sending the part back?

WWFA
DTFA
DMR
CDMR

Answer(s): C

Explanation:

When Dell Technical Support requests a part to be sent back for analysis, a Defective Material Return (DMR) process must be completed. The DMR process involves several key steps:
Receive DMR Authorization:
Dell Technical Support provides a DMR number and return instructions.
Complete Required Documentation:
Fill out any forms detailing the part's serial number, failure symptoms, and troubleshooting steps taken.
Prepare the Part for Shipment:
Properly package the defective part using anti-static materials and cushioning to prevent further damage.
Include DMR Documentation:
Attach the DMR paperwork with the shipment to ensure correct processing.
Ship the Part:
Send the package to the designated Dell Logistics center. Completing the DMR process allows Dell to study the defective part, which can lead to product improvements and enhanced support services.

Reference:

Dell PowerScale Field Replacement Unit (FRU) Procedures DMR Process
Dell Logistics Return Guidelines Shipping and Documentation Requirements Dell Technical Support Policies Defective Material Return Instructions

Reveal Solution Next Question

QUESTION: 8

What must be enabled in SMB to ensure nondisruptive upgrades?

SMB multichannel
SMB encryption
SMB direct
SMB continuous availability

Answer(s): D

Explanation:

To ensure nondisruptive upgrades in an SMB environment, SMB Continuous Availability (CA) must be enabled. SMB CA allows file shares to remain accessible without interruption during planned maintenance or unexpected node failures.
Key features of SMB Continuous Availability:
Transparent Failover:
Client sessions persist seamlessly when the SMB service fails over to another node.
State Preservation:
Open files, locks, and session states are maintained during the failover.
High Availability:
Enhances the cluster's ability to provide uninterrupted service.
Steps to enable SMB Continuous Availability:
Verify OneFS Version:
Ensure the cluster is running OneFS version that supports SMB 3.0 or higher.
Enable SMB CA on the Cluster:
Use the OneFS WebUI or CLI to enable Continuous Availability for SMB shares.
Configure SMB Shares:
Set the "Continuous Availability" option on the specific SMB shares that require it.
Client Requirements:
Clients must be running Windows 8 or Windows Server 2012 (or later) to support SMB CA. By enabling SMB Continuous Availability, upgrades and maintenance can be performed without disrupting client access to file shares.

Reference:

Dell PowerScale OneFS SMB Administration Guide Configuring SMB Continuous Availability Dell PowerScale OneFS Upgrade Planning Guide Ensuring Nondisruptive Upgrades Microsoft SMB Protocol Documentation SMB 3.0 Features

Reveal Solution Next Question

Free D-PSC-MN-01 Exam Braindumps (page: 2)

QUESTION: 5

Explanation:

QUESTION: 6

Explanation:

Reference:

QUESTION: 7

Explanation:

Reference:

QUESTION: 8

Explanation:

Reference: