QUESTION: 29

When planning for a Dell EMC PowerStore X implementation, how many IP addresses are required for the storage network?

Answer(s): D

Explanation:

For a Dell EMC PowerStore X implementation, a minimum of six IP addresses are required for the storage network. This is to accommodate the various components that need network connectivity within the PowerStore infrastructure.
The allocation of these IP addresses typically includes:
· Two IP addresses for the storage processors or nodes within the PowerStore appliance.
· Two IP addresses for the management interfaces.
· Two additional IP addresses for redundancy or other network services. It's important to plan the network configuration carefully to ensure that there are enough IP addresses available for all required services and for future expansion. For optimization and best practices in IP address allocation, administrators should refer to the Dell EMC PowerStore Networking Guide for Storage Services. This guide provides detailed information on network requirements, including IP address allocation and network design considerations for PowerStore systems.

Reveal Solution Next Question

QUESTION: 30

What are the recommended number of network switches in a Dell EMC PowerStore T environment?

Answer(s): D

Explanation:

In a Dell EMC PowerStore T environment, the recommended number of network switches is two. This recommendation is based on best practices for general network performance and high availability. Using two switches allows for redundancy and ensures that if one switch fails, the other can continue to handle the network traffic without interruption. The use of multiple switches connected with technologies like Virtual Link Trunking (VLT) and Link Aggregation Control Protocol (LACP) or their equivalents is advised. Each PowerStore node should have connectivity to all linked switches to maintain high availability and optimal network performance.
For detailed network design and switch configuration recommendations, administrators should refer to the Dell PowerStore Networking Guide for PowerStore T Models and other official Dell documentation. These resources provide comprehensive guidelines on setting up the network infrastructure to support PowerStore T systems effectively.

Reveal Solution Next Question

QUESTION: 31

The "svc_rescue_state list" shows a node in service mode. How can the node be returned to normal mode?

svc_rescue_state quit
svc_rescue_state clear
svc_rescue_state normal
svc_rescue_state exit

Answer(s): B

Explanation:

To return a node from service mode to normal mode in a Dell EMC PowerStore system, the svc_rescue_state clear command should be used. This command clears the service mode state of the node and prepares it to return to normal operational mode.
Here are the steps to perform this action:
Log in to the appliance from an SSH client.
Run the svc_rescue_state clear command to clear the boot mode. Then, run the svc_node reboot command to reboot the node and return it to normal mode. After the reboot, you can verify that the node has returned to normal mode by running the svc_rescue_state list command again.
It is important to follow these steps carefully to ensure that the node transitions back to normal mode without any issues. For more detailed instructions or if you encounter any problems during this process, refer to the Dell EMC PowerStore Service Scripts Guide or contact Dell EMC Support for assistance.

Reveal Solution Next Question

QUESTION: 32

When a Dell EMC PowerStore node powers up in service mode, what are the commands and sequence used from the appliance SSH client to restore the node back to normal?

svc_node restart svc_rescue_state start
svc_node shutdown svc_rescue_state clear
svc_rescue_state clear svc_node reboot
svc_rescue_state normal svc_node start

Answer(s): C

Explanation:

When a Dell EMC PowerStore node powers up in service mode, the commands and sequence used from the appliance SSH client to restore the node back to normal are as follows:
Run the svc_rescue_state clear command to clear the boot mode and take the node out of service mode.
Then, run the svc_node reboot command to reboot the node and return it to normal operational mode.
It is important to follow this sequence to ensure that the node exits service mode correctly and reboots into normal mode without any issues. For more detailed instructions or if you encounter any problems during this process, refer to the Dell EMC PowerStore Service Scripts Guide or contact Dell EMC Support for assistance.

Reveal Solution Next Question

Free D-PST-MN-A-24 Exam Braindumps (page: 8)

QUESTION: 29

Explanation:

QUESTION: 30

Explanation:

QUESTION: 31

Explanation:

QUESTION: 32

Explanation: