A user is attempting to write tiles to a Power Flex File share The share was created with default settings and contains approximately 15 000 files Ten days ago the number of files exceeded the soft limit quota but is still below the hard limit quota What happens if the user attempts to write a new file to the share location?
Answer(s): C
In PowerFlex File shares, when a soft limit quota is exceeded, it triggers a grace period during which users can still write data to the share. The grace period is a predefined time frame that allows users to either reduce the amount of stored data or to adjust the quota settings. As long as the hard limit quota has not been reached, users can continue to write files to the share, even if the soft limit has been exceeded and the grace period is in effect.The soft limit is essentially a warning threshold that alerts users that they are approaching the maximum allowed capacity, but it does not immediately prevent new writes. The hard limit, on the other hand, is a strict limit that, once reached, will prevent any further writes to the share until the stored data is reduced below the hard limit or the quota is increased. Since the question states that the number of files is still below the hard limit quota, the user will be able to write a new file to the share location. Therefore, the correct answer is C. The file is written as the hard limit has not been reached.
DRAG DROP (Drag and Drop is not supported)Place the steps to set up remote replication on the Powerflex system in the correct order
Answer(s): A
The correct sequence of steps to set up remote replication on the PowerFlex system is as follows:Install target PowerFlex system: Before replication can be set up, there must be a target system in place to receive the replicated data.Exchange root certificates: This is a security measure to ensure that communication between the source and target systems is secure.Add a Replication Peer: This involves configuring the target system as a replication partner in the source system's configuration.Configure replication volumes: Finally, specific volumes on the source system are configured to replicate to the target system.Setting up remote replication in a PowerFlex system involves a series of steps that establish the necessary components and configurations for the replication process. The sequence begins with the installation of the target PowerFlex system, which will serve as the destination for the replicated dat a. Next, root certificates are exchanged between the source and target systems to ensure secure communication. The target system is then added as a Replication Peer within the source system's configuration. Lastly, the volumes intended for replication are configured on the source system to complete the setup process. This sequence ensures that the replication is secure, reliable, and correctly configured to maintain data integrity and availability across both systems.
An administrator is adding an NVMe device to an existing storage pool They provide the following details in the Add Storage Device to SDS dialog box· Device Path /dev/disk/by-id'Dell_Express_Flash_NVMe_PM1725_V6TB_SFF_ _S2JPNA0J500141· Device Name NVMe A. 1.6 TB· Storage Pool SP-1What is the result of this action'?
When adding an NVMe device to an existing storage pool in PowerFlex, the details provided in the "Add Storage Device to SDS" dialog box must be accurate and follow the correct syntax. In the scenario provided, the device path contains an invalid character (an apostrophe) and an incorrect format, which would cause the device addition to fail. Here's a breakdown of the process and where the error occurs:Device Path: The device path should be a valid Linux device path, typically starting with /dev/disk/by- id/. The path provided contains an apostrophe (') which is not a valid character in Linux file paths and would result in an error.Device Name: The device name should be a simple identifier without spaces or special characters. The name provided, "NVMe A. 1.6 TB", contains spaces and periods, which are not typical for device names and could potentially lead to issues, although the primary cause of failure is the invalid device path.Storage Pool: The storage pool name "SP-1" is a valid identifier, but it is contingent on the correct device path and name for the device to be added successfully. The result of the action, given the invalid device path, would be that the device addition fails. It is crucial to ensure that all details entered in the dialog box adhere to the expected formats and do not contain invalid characters to avoid such failures.This explanation is based on the standard practices for device path naming conventions in Linux systems and the configuration guidelines for PowerFlex systems as described in Dell's official documentation. Correcting the device path by removing the invalid character and ensuring the proper format would resolve the issue and allow the device to be added to the storage pool successfully.
A customer has ordered five servers with NVDlMMs Each server has 5 x 3 84 TB SAS and 5 x 3 84 T8 NVMe disks They want to ensure that the highest capacity ot storage is available to the system Which design provides the required storage pool structure''
To maximize the storage capacity available to the system while utilizing NVDIMMs, SAS, and NVMe disks, the design should include both a Storage Pool and an Acceleration Pool. The Storage Pool will be used for the bulk storage provided by the SAS disks, while the Acceleration Pool, leveraging the high-speed NVMe disks, will be used to accelerate the performance of the storage system. The use of NVDIMMs in PowerFlex is associated with enabling fine-granularity storage pools that provide compression, which is beneficial for space efficiency, especially with heavy snapshot use. This configuration allows for the creation of a storage pool that can take advantage of the NVDIMMs' capabilities for compression and the high capacity of the SAS disks, while the NVMe disks in the Acceleration Pool provide high-performance storage for more demanding workloads. Therefore, the correct answer is A. One Storage Pool and one Acceleration Pool, as this design will provide the highest capacity of storage available to the system while also ensuring optimal performance through the use of NVMe disks in the Acceleration Pool.
Post your Comments and Discuss Dell D-PWF-DS-23 exam with other Community members:
Ray commented on August 20, 2024 The questions I faced were mostly new, with only one or two matching what I'd seen in the dumps. My takeaway is that it's essential to study the Dell guide thoroughly to be well-prepared. Anonymous upvote
Hazel Pacheco commented on August 16, 2024 This is not the latest version, please update Anonymous upvote
Our website is free, but we have to fight against bots and content theft. We're sorry for the inconvenience caused by these security measures. You can access the rest of the D-PWF-DS-23 content, but please register or login to continue.