What is the purpose of penultimate hop popping?
Answer(s): A
Penultimate hop popping (PHP) is a function performed by certain routers in an MPLS enabled network. It refers to the process whereby the outermost label of an MPLS tagged packet is removed by a label switch router (LSR) before the packet is passed to an adjacent label edge router (LER). The purpose of PHP is to reduce the load on the LER, as it saves one cycle of label lookup. The LER can forward the packet based on its IP header or another label in the stack, without having to process the outer label. PHP functionality is achieved by the LER advertising a label with a value of 3 to its neighbors. This label is defined as "implicit-null" and informs the neighboring LSRs to perform PHP12.
Penultimate hop popping - Wikipedia, MPLS Penultimate hop popping - NetworkLessons.com
Which mismatched field would cause an IS-IS adjacency between two routers to fail?
MTU mismatch would cause an IS-IS adjacency between two routers to fail. MTU stands for maximum transmission unit, which is the maximum size of a packet that can be transmitted on a link. IS-IS hellos are padded to the full MTU size, partly to allow a router to implicitly communicate its MTU to its neighbors. If two routers have different MTUs on their interfaces, they will not be able to exchange hellos properly, and their adjacency will not form or will be dropped34. To solve this problem, the MTUs on both interfaces must be configured to match. SEL, context, and SysID are not fields that would cause an IS-IS adjacency failure. SEL stands for selector, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the SEL must always be 005. Context is not a field in IS-IS packets, but rather a term used to describe the scope of routing information in different levels or areas6. SysID stands for system identifier, which is a six-octet field that uniquely identifies a router within an area. SysID does not have to match between two routers for them to form an adjacency7.
MTU Mismatch Problem in IS-IS - Cisco, IS-IS adjacency is not formed due to MTU mismatch - Cisco Community, IS-IS NSAP address - Cisco Community, Understanding IS-IS Routing Contexts - Juniper Networks, IS-IS - Nokia
Regarding the BGP decision algorithm, which two statements are correct? (Choose two.)
Answer(s): A,C
Regarding the BGP decision algorithm, two statements that are correct are:A higher local-preference attribute will be favored over a lower local-preference attribute. The local- preference attribute is used by BGP routers within an AS to indicate their preference for an exit point from the AS. A higher value means a more preferred path. The local-preference attribute is exchanged only between iBGP peers and does not leave the AS boundary89. A path cannot be considered if the next-hop is inaccessible. The next-hop attribute is used by BGP routers to determine where to forward packets for a given destination prefix. The next-hop attribute is usually set to the IP address of the eBGP neighbor that advertises the prefix. If there is no IGProute to reach the next-hop address, the path is marked as invalid and ignored by BGP1011.The other two statements are incorrect because:The most important criteria is not the administrative distance, but rather the weight attribute. The administrative distance is used by routers to choose between routes from different routing protocols, not within BGP. The weight attribute is a Cisco-specific attribute that is used by BGP routers to prefer one path over another within the same router. The weight attribute is local to the router and not advertised to any peers1213.A lower local-preference attribute will not be favored over a higher local-preference attribute, as explained above.
BGP Best Path Selection Algorithm - Cisco, Understanding BGP Local Preference Attribute- NetworkLessons.com, BGP Next Hop Attribute Explained - NetworkLessons.com, BGP Next Hop Processing - Cisco Press, BGP Weight Attribute Explained - NetworkLessons.com, Understanding BGPWeight Attribute - Cisco Community
In OSPFv2, which route characteristic is used to determine the best path?
Answer(s): C
In OSPFv2, the route characteristic that is used to determine the best path is the cost. The cost is a metric that represents the link bandwidth, delay, reliability, or other factors. The cost is inversely proportional to the bandwidth, meaning that a higher bandwidth link has a lower cost. The cost of a route is calculated by adding the costs of all links along the path. OSPFv2 uses the following formula to calculate the cost of an interface:Cost = Reference bandwidth / Interface bandwidth in bps The reference bandwidth is a constant value that can be configured by the network administrator. By default, it is 100 Mbps. The interface bandwidth is the actual bandwidth of the interface in bits per second. For example, if an interface has a bandwidth of 10 Mbps, its cost would be 100 Mbps / 10 Mbps = 101415.OSPFv2 does not use jitter, packet loss, or delay as route characteristics to determine the best path. Jitter is the variation in latency or delay between packets. Packet loss is the percentage of packets that are dropped or corrupted during transmission. Delay is the time it takes for a packet to travel from source to destination. These characteristics are not part of the OSPFv2 protocol and are not advertised in OSPFv2 LSAs1617.
OSPF Metric cost Calculation Formula Explained - ComputerNetworkingNotes, OSPF Cost OSPF Routing Protocol Metric Explained - Study-CCNA, Open Shortest Path First - Wikipedia, OSPF Metric = Cost - Cisco
An operator wants to ensure that they can differentiate their traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone.Which three fields would be used? (Choose three.)
Answer(s): A,C,E
To differentiate traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone, an operator can use the following three fields:Traffic Class (TC): This is a 3-bit field in the MPLS label that can be used to indicate the priority or class of service (CoS) of the packet. The TC field can be mapped to the DSCP field in the IP header or the PCP field in the Ethernet header. The TC field can be used by MPLS routers to apply different per- hop behaviors (PHBs) such as queuing, scheduling, and dropping policies to different traffic classes12.DSCP: This is a 6-bit field in the IP header that can be used to mark packets according to the differentiated services (DiffServ) model. The DSCP field can indicate the per-hop behavior (PHB) that the packet should receive at each router along its path. The DSCP field can be mapped to the TC field in the MPLS label or the PCP field in the Ethernet header. The DSCP field can be used by IP routers to provide QoS for different traffic types34.PCP: This is a 3-bit field in the Ethernet header that can be used to mark packets according to the IEEE 802.1Q standard. The PCP field can indicate the priority or class of service (CoS) of the packet on an Ethernet LAN. The PCP field can be mapped to the TC field in the MPLS label or the DSCP field in the IP header. The PCP field can be used by Ethernet switches to provide QoS for different traffic types56.
MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering, MPLS Traffic Engineering - DiffServ-Aware Traffic Engineering Configuration Guide, Differentiated services - Wikipedia, DSCP and Precedence Values - Cisco, 802.1Q VLAN IDs and Ethernet Interface Types - Juniper Networks, Introduction to Virtual LANs (VLANs) and Tagging - Ubiquiti Support and Help Center
Post your Comments and Discuss Ericsson ECP-206 exam prep with other Community members:
Our website is free, but we have to fight against AI bots and content theft. We're sorry for the inconvenience caused by these security measures. You can access the rest of the ECP-206 content, but please register or login to continue.