Exhibit.The administrator configured the IPsec tunnel VPN1 on a FortiGate device with the parameters shown in exhibit.Based on the configuration, which three conclusions can you draw about the characteristics and requirements of the VPN tunnel? (Choose three.)
Answer(s): B,C,E
This configuration demonstrates a typical IPsec setup for SD-WAN overlays where the hub side requires a manually defined tunnel IP address, and the spoke can be flexibly configured, including interoperability with third-party IPsec devices. As described in the Fortinet SD-WAN Architect Guide:"For some overlays, the tunnel interface IP is configured statically on the hub side, which allows more control over overlay subnetting and facilitates the use of user-defined overlay IP addresses. This approach is also a requirement for compatibility with non-FortiGate endpoints, such as third- party IPsec devices that may not support dynamic address assignment via IKE or proprietary mechanisms." This enables hybrid SD-WAN environments and advanced designs involving external partners or cloud services. Overlay IP flexibility is critical for route control and segmentation.
FortiOS 7.4 SD-WAN Reference Architecture, "Overlay IP Address Management"SD-WAN 7.4 Concept Guide, Section: "Interoperability with Third-Party Devices"
You have a FortiGate configuration with three user-defined SD-WAN zones and two members in each of these zones. One SD-WAN member is no longer in use in health-check and SD-WAN rules. You want to delete it.What happens if you delete the SD-WAN member from the FortiGate GUI?
Answer(s): A
Refer to the exhibits.The exhibits show the source NAT (SNAT) global setting. port2 interface settings, and the routing table on FortiGate.The administrator increases the member priority on port2 to 20.Upon configuration changes and the receipt of new packets, which two actions does FortiGate perform on existing sessions established over port2? (Choose two.)
Answer(s): D,E
When the member priority of a port is increased (e.g., port2 to 20), FortiGate evaluates existing sessions and applies "dirty" flags where applicable. The SD-WAN session management mechanism is described in detail: "Upon a change in SD-WAN member priority, all existing sessions using that member are marked as dirty. For SNAT sessions, the gateway information is updated to ensure future packets are routed through the newly preferred member, in this case, port1. This automatic re- evaluation allows SD-WAN to dynamically respond to topology or priority changes, maintaining optimal routing." This is fundamental to seamless failover and session persistence in Fortinet SD- WAN, ensuring active flows are redirected based on updated priorities or health status.
FortiOS 7.4 SD-WAN Concept Guide, "Session Management During Path Change"FortiGate CLI diagnose sys session list
Refer to the exhibits.The exhibits show the configuration for SD-WAN performance. SD-WAN rule, the application IDs of Facebook and YouTube along with the firewall policy configuration and the underlay zone status.Which two statements are true about the health and performance of SD-WAN members 3 and 4? (Choose two.)
Answer(s): B,D
When you use the command diagnose sys session list, how do you identify the sessions that correspond to traffic steered according to SD-WAN rules?
Answer(s): D
When using the diagnose sys session list command, SD-WAN-specific session steering is indicated by the presence of the sdwan_service_id field in the session data. This identifier ties the session directly to a specific SD-WAN rule or service. As noted in the Fortinet documentation: "Sessions that are handled according to SD-WAN rules will include a service ID tag (sdwan_service_id) in their session listing. This allows administrators to correlate live sessions with SD-WAN policy matches for troubleshooting and visibility." This is a crucial diagnostic tool, as it distinguishes between traffic managed by traditional routing and that explicitly controlled by SD-WAN steering logic, aiding in operational insight and troubleshooting.
FortiOS 7.4 CLI Reference, "diagnose sys session list: SD-WAN Service ID Tagging"SD-WAN 7.4 Concept Guide, Section: "Session Identification for SD-WAN Traffic"
Post your Comments and Discuss Fortinet FCSS_SDW_AR-7.6 exam dumps with other Community members:
DynamoDB
S3
Cognito
RDS
EFS
/sbin/init
/etc/inittab
/etc/rc.d
/etc/init.d
/lib/init.so
/etc/rc.d/rcinit
/proc/sys/kernel/init
/boot/init
/bin/init
Amazon S3 Intelligent-Tiering
S3 Lifecycle
S3 Glacier Flexible Retrieval
Amazon Athena
Amazon EFS
EC2 instance store
ElastiCache for Redis
S3 Glacier Deep Archive
AWS Lake Formation
Amazon EMR Spark jobs
Amazon Kinesis Data Streams
Amazon DynamoDB
Defender for Endpoint
Defender for Identity
Defender for Cloud Apps
Defender for Office 365
S3 Object Lock
SFTP
AWS Transfer Family
Amazon SQS
API Gateway
Lambda
usage plan
AWS WAF
Amazon ECS
Application Load Balancer
AWS Global Accelerator
Network Load Balancer
EC2
Auto Scaling group
CloudFront
ALB
AWS PrivateLink
CRR
SSE-S3
Athena
SSE-KMS
RDS Custom for Oracle
s3:GetObject
Our website is free, but we have to fight against AI bots and content theft. We're sorry for the inconvenience caused by these security measures. You can access the rest of the FCSS_SDW_AR-7.6 content, but please register or login to continue.