MULTIPLE CHOICERefer to the exhibit, which shows the omitted output of a session table entry.Which two statements are true? (Choose two.)
Answer(s): C,D
In the provided session table output, the following details justify the answers:Policy ID Match: The line policy_id=1 directly confirms that this session was matched by Firewall Policy ID 1. According to Fortinet's session table documentation, the policy_id field always references the policy that allowed this session, so this is a clear indicator.Session Offloading: The presence of the strings npu_state, ips_offload, and notably the NPU info section such as offload=8/8, ips_offload=1/1 shows that this session has been offloaded to the Network Processor Unit (NPU). Fortinet technical documentation states that 'offload' values greater than zero in both directions (and an NPU info section) affirm that NPU hardware processing (fast path) is handling this traffic, thus the session is not being handled in software only.Other options:VLAN Tagging (vlan=0x0000/0x0000): This means no VLAN tag is assigned to this session.NP7: The actual NPU model handling the session isn't exposed in this snippet--the offload parameters shown are generic and not specific to NP7 hardware, so it cannot be concluded from the session data.Fortinet Technical Tip: FortiGate Session Table and NPU OffloadingFortiOS Diagnostics Guide: Policy ID, Offload, and VLAN Session Table Fields
MULTIPLE CHOICERefer to the exhibit.Assuming a default configuration, which three statements are true? (Choose three.)
Answer(s): B,C,E
Fortinet Technical Note: RPF Default Configuration and Routing Table MatchingFortiGate Administration Guide: Routing and Asymmetric Routing ControlsCommunity Knowledgebase: Route Lookups and RPF Enforcement on FortiOS
MULTIPLE CHOICEWhich two statements about Security Fabric communications are true? (Choose two.)
FortiTelemetry is a critical part of Security Fabric communications and requires explicit configuration for each participating FortiGate interface. The administrative access setting 'fabric' (corresponding to FortiTelemetry) must be manually enabled per interface on both upstream and downstream devices. This is performed in the GUI under Administrative Access or via the CLI using the commandset allowaccess fabricfor the relevant network interface. Without this step, FortiTelemetry communications will not occur on that interface.Additionally, the default communication between downstream and upstream FortiGate units in the Security Fabric is over TCP port 8013. This port is well-documented as the standard for Security Fabric and FortiTelemetry connections, and must be open and permitted across the network path for connectivity and status enforcement between units. The downstream FortiGate initiates the connection to the upstream via this port unless otherwise configured. This has also been documented as a PCI-relevant port, showing its default usage.Other options:Neighbor Discovery in FortiOS uses IPv6 ND protocol, not TCP.FortiTelemetry port (8013) can be modified, but the interface Administrative Access for the Security Fabric must be manually enabled; Neighbor Discovery port modification is not documented as a supported change for FortiGate.FortiGate/FortiOS Administration Guide: Enabling FortiTelemetry (fabric) on interfacesFortinet Technical Tip: FortiTelemetry uses TCP port 8013 by defaultPCI compliance documentation on port 8013 usage for Security FabricFortinet Security Fabric setup procedures and interface options
Refer to the exhibit, which contains the output of diagnose vpn tunnel list.Which command will capture ESP traffic for the VPN named DialUp_0?
Answer(s): D
The exhibit with the diagnose vpn tunnel list output is not visible. The correct command to capture ESP (Encapsulating Security Payload) traffic for a specific VPN tunnel typically involves using a packet capture or debug command that targets the tunnel interface. For a VPN named DialUp_0, this would likely be a tcpdump or diagnose sniffer command specifying the tunnel name or interface.
MULTIPLE CHOICEExhibit.Refer to the exhibit, which shows the output of diagnose automation test.What can you observe from the output? (Choose two.)
Answer(s): A,D
Without access to the exhibit showing the diagnose automation test output, specific observations cannot be determined. However, this command typically shows the results of automation trigger and action testing, which might display execution status, timing information, trigger conditions being met, action outcomes, or error messages. The answer would depend on what specific details are visible in the output.
Post your Comments and Discuss Fortinet NSE7_FSN_AR-7.6 exam prep with other Community members:
Our website is free, but we have to fight against AI bots and content theft. We're sorry for the inconvenience caused by these security measures. You can access the rest of the NSE7_FSN_AR-7.6 content, but please register or login to continue.