support@Free-Braindumps.com
Register Login
Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
CrowdStrike
Anthropic
All Vendors
  1. Home
  2. Exams
  3. Cisco
  4. 300-410

Free 300-410 Exam Braindumps
Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) Questions 241–248 (page: 32)

Updated On: 9-Jul-2026
Page 32 of 81
PDF with 640 Questions

Refer to the exhibit. The R2 loopback interface is advertised with RIP and EIGRP using default values. Which configuration changes make R1 reach the R2 loopback using RIP?

  1. R1(config)#router rip R1(config-router)#distance 90
  2. R1(config)#router eigrp 1 R1(config-router)#distance eigrp 130 120
  3. R1(config)#router rip R1(config-router)#distance 100
  4. R1(config)#router eigrp 1 R1(config-router)#distance eigrp 120 120

Answer(s): B



Refer to the exhibit. A network administrator notices these console messages from host 10.11.110.12 originating from interface E1/0. The administrator considers this an unauthorized attempt to access SNMP on R1. Which action prevents the attempts to reach R1 E1/0?

  1. Configure IOS control plane protection using ACL 90 on interface E1/0.
  2. Create an inbound ACL on interface E1/0 to deny SNMP from host 10.11.110.12.
  3. Add a permit statement including the host 10.11.110.12 into ACL 90.
  4. Configure IOS management plane protection using ACL 90 on interface E1/0.

Answer(s): D



Refer to the exhibit. R6 should reach R1 via R5>R2>R1. Which action resolves the issue?

  1. Decrease the cost to 2 between R6-R5-R2.
  2. Increase the cost to 61 between R2-R3-R1.
  3. Increase the cost to 61 between R2 and R3.
  4. Decrease the cost to 41 between R2 and R1.

Answer(s): C



An engineer failed to run diagnostic commands on devices using Cisco DNA Center. Which action in Cisco DNA Center resolves the issue?

  1. Enable Secure Shell.
  2. Enable APIs.
  3. Enable CDP.
  4. Enable Command Runner.

Answer(s): D



Refer to the exhibit. The static route is not present in the routing table of an adjacent OSPF neighbor router. Which action resolves the issue?

  1. Configure a permit 20 statement to the route map to redistribute the static route.
  2. Configure the next-hop interface at the end of the static route for it to get redistributed.
  3. Configure the next hop of 10.20.20.1 in the prefix list DMZ-STATI
  4. Configure the subnets keyword in the redistribution command.

Answer(s): D



Refer to the exhibit. Packets arriving from source 209.165.200.215 must be sent with the precedence bit set to 1, and packets arriving from source 209.165.200.216 must be sent with the precedence bit set to 5. Which action resolves the issue?

  1. set ip precedence critical in route-map Texas permit 20
  2. set ip precedence critical in route-map Texas permit 10
  3. set ip precedence priority in route-map Texas permit 20
  4. set ip precedence immediate in route-map Texas permit 10

Answer(s): A



Refer to the exhibit. An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP, where the metric must be added when traversing through multiple hops to start an external route of 20. The engineer notices that the external metric is fixed and does not add at each hop. Which configuration resolves the issue?

  1. R2(config)#access-list 10 permit
    192.168.10.0 0.0.0.255
    R2(config)#access-list 10 permit
    192.168.20.0 0.0.0.255
    !
    R2(config)#route-map RD permit 10
    R2(config-route-map)#match ip address 10
    R2(config-route-map)#set metric 20
    R2(config-route-map)#set metric-type type-2
    !
    R2(config)#router ospf 10
    R2(confjg-router)#redistribute eigrp 10
    subnets route-map RD
  2. R2(config)#access-list 10 permit
    192.168.10.0 0.0.0.255
    R2(config)#access-list 10 permit
    192.168.20.0 0.0.0.255
    !
    R2(config)#route-map RD permit 10
    R2(config-route-map)#match ip address 10
    R2(config-route-map)#set metric 20
    R2(config-route-map)#set metric-type type-1
    !
    R2(config)#router ospf 10
    R2(config-router)#redistribute eigrp 10
    subnets route-map RD
  3. R1(config)#access-list 10 permit
    192.168.10.0 0.0.0.255
    R1(config)#access-list 10 permit
    192.168.20.0 0.0.0.255
    !
    R1(config)#route-map RD permit 10
    R1(config-route-map)#match ip address 10
    R1(config-route-map)#set metric 20
    R1(config-route-map)#set metric-type type-1
    !
    R1(config)#router ospf 10
    R1(config-router)#redistribute eigrp 10
    subnets route-map RD
  4. R1(config)#access-list 10 permit
    192.168.10.0 0.0.0.255
    R1(config)#access-list 10 permit
    192.168.20.0 0.0.0.255
    !
    R1(config)#route-map RD permit 10
    R1(config-route-map)#match ip address 10
    R1(config-route-map)#set metric 20
    R1(config-route-map)#set metric-type type-2
    !
    R1(config)#router ospf 10
    R1(config-router)#redistribute eigrp 10
    subnets route-map RD

Answer(s): B

Explanation:

We have to set the metric-type to E1, which includes the internal cost to ASBR added to the externalcost-> Only Option B and Option C are correct.We need to redistribute on R2, not R1-> Only Option B is correct.



An engineer notices that R1 does not hold enough log messages to identify the root cause during troubleshooting. Which command resolves this issue?

  1. #logging buffered 4096 critical
  2. #logging buffered 16000 critical
  3. (config)#logging buffered 16000 informational
  4. (config)#logging buffered 4096 informational

Answer(s): C



  PDF
Viewing page 32 of 81
Viewing questions 249 - 256 out of 640 questions


Post your Comments and Discuss Cisco 300-410 exam prep with other Community members:

AI Tutor AI Tutor 👋 I’m here to help!