Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
Splunk
ServiceNow
All Vendors
  2. Home
  3. Exams
  4. Cisco
  5. 350-401

Cisco 350-401 Exam Questions
Implementing Cisco Enterprise Network Core Technologies (ENCOR) (Page 35 )

Updated On: 9-Mar-2026
Page 35 of 193
PDF with 1067 Questions

Refer to the exhibit. Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?

  1. ip nat inside source list 10 interface FastEthernet0/2 overload
  2. ip nat inside source list 10 interface FastEthernet0/1 overload
  3. ip nat outside source static 209.165.200.225 10.10.10.0 overload
  4. ip nat outside source list 10 interface FastEthernet0/2 overload

Answer(s): B



Refer to the exhibit. What are two effects of this configuration? (Choose two.)

  1. If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online.
  2. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online.
  3. R1 becomes the active router.
  4. R1 becomes the standby router.
  5. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online.

Answer(s): C,E



Refer to the exhibit. An engineer must ensure that all traffic entering AS 200 from AS 100 chooses Link 2 as an entry point. Assume that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers. Which configuration accomplishes this task?

  1. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 200 200 200 R3(config)#router bgp 200 R3#(config-router)#neighbor 10.1.1.1 route-map PREPEND out
  2. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 100 100 100 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND in
  3. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 200 200 200 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND out
  4. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 100 100 100 R3(config)#router bgp 200 R3(config-router)#neighbor 10.1.1.1 route-map PREPEND in

Answer(s): A



Which DHCP option provides the CAPWAP APs with the address of the wireless controller(s)?

  1. 43
  2. 66
  3. 69
  4. 150

Answer(s): A



Refer to the exhibit.

Which two commands ensure that DSW1 becomes root bridge for VLAN 10? (Choose two.)

  1. DSW1(config)#spanning-tree vlan 10 priority 4096
  2. DSW1(config)#spanning-tree vlan 10 priority root
  3. DSW2(config)#spanning-tree vlan 10 priority 61440
  4. DSW1(config)#spanning-tree vlan 10 port-priority 0
  5. DSW2(config)#spanning-tree vlan 20 priority 0

Answer(s): A,C

Explanation:

DSW1(config)#spanning-tree vlan 10 priority 4096 < -- This is listed
DSW1(config)#spanning-tree vlan 10 priority root < -- this is not valid
DSW1(config)#spanning-tree vlan 10 root primary < -- This is not listed, but should be the correct command



Viewing page 35 of 193
Viewing questions 171 - 175 out of 1067 questions



Post your Comments and Discuss Cisco 350-401 exam dumps with other Community members:

350-401 Exam Discussions & Posts

AI Tutor