A customer has a requirement to deploy a cloud service and needs to have full control over the underlying OS, data and applications.Which cloud model meets this requirement?
Answer(s): D
Traditional IT is responsible for Application, Data, Runtime, Middleware, OS, Virtualization, Servers, Storage, Networking.IaaS = Infrastructure as a Service - The customer is responsible for OS, Virtualization, Servers, Storage, Networking.SaaS = Software as a Service - The software is deployed by the cloud provider - Customer is responsible for nothing.PaaS = Platform as a Service - Software can be deployed by the customer building their own application | is responsible for Data and Application.
Refer to the exhibit.A flapping link issue has been reported on the vPC keepalive link. A packet capture has been activated on the Cisco Nexus switch.What is the destination IP address of the vPC keepalive packets that are sent by the switch?
Answer(s): A
3200 is the default UDP port for keepalive packets. Just look for the first line with port 3200 and note the destination IP, which is 192.168.254.4.
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus3000/sw/interfaces/92x/b-cisco-nexus-3000-nx-os-interfaces-configuration-guide-92x/b-cisco-nexus-3000-nx-os-interfaces-configuration-guide-92x_chapter_0110.html
Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch.Which two technologies should be implemented to reduce disruptions to the network during the upgrade? (Choose two.)
Answer(s): A,B
vPC leverages both hardware and software redundancy aspects:ג— vPC uses all port-channel member links available so that in case an individual link fails, hashing algorithm will redirect all flows to the remaining links.ג— vPC domain is composed of two peer devices. Each peer device processes half of the traffic coming from the access layer. In case a peer device fails, the other peer device will absorb all the traffic with minimal convergence time impact.Best Practices for HSRP/VRRP and vPCThis section describes best practices for using HSRP (Hot Standby Router Protocol) or VRRP (Virtual Router Redundancy Protocol) with vPC.HSRP/VRRP active/active with vPC* HSRP (Hot Standby Router Protocol) and VRRP (Virtual Router Redundancy Protocol) are both network protocols that provides high availability for servers IP default gateway.* vPC domain at aggregation layer usually performs L2/L3 boundary so each vPC peer device is configure with interface VLAN (or SVI) and HSRP or VRRP runs on top of this interface.* HSRP and VRRP in the context of vPC have been improved from a functional and implementation standpoint to take full benefits of the L2 dual-active peer devices nature offered by vPC technology.
https://www.cisco.com/c/dam/en/us/td/docs/switches/datacenter/sw/design/vpc_design/vpc_best_practices_design_guide.pdf
Refer to the exhibit.What is the result of running the command presented?
Answer(s): C
When you restart PIM, the following tasks are performed:* The PIM database is deleted.* The MRIB and MFIB are unaffected and forwarding of traffic continues.* The multicast route ownership is verified through the MRIB.* Periodic PIM join and prune messages from neighbors are used to repopulate the database.
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/multicast/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Multicast_Routing_Configuration_Guide/b_Cisco_Nexus_9000_Series_NX-OS_Multicast_Routing_Configuration_Guide_chapter_011.html
Refer to the exhibit.What is the reason the system-fm-vrrp checkpoint was created?
Reasons that could trigger automated system checkpoints are highlighted below:* License expiration of a feature* Disabling a feature with the no feature command* Removing an instance of a Layer 3 protocolThe system-generated checkpoint name convention has the format system-fm-feature. To help illustrate this automated feature we attempted to disable the VRRP feature on our Nexus 5000 therefore triggering the system to create a checkpoint. First we confirm the VRRP feature is enabled by issuing the show feature | include vrrp command then disable it and then verify it has been disabled:Notice that the system now shows a second checkpoint system-fm-vrrp which did not previously exist. This second checkpoint was created automatically by theNexus as soon as we disabled the vrrp feature.
https://www.firewall.cx/cisco-technical-knowledgebase/cisco-data-center/1202-cisco-nexus-checkpoint-rollback-feature.html
Post your Comments and Discuss Cisco 350-601 exam dumps with other Community members:
Steven Commented on August 02, 2025 First time trying out, will update the result Anonymous
wtb Commented on July 13, 2025 these questions are over 2 years old UNITED STATES
Abbas Commented on May 21, 2025 Refer to the exhibit. Which action is taken to ensure that the relay agent forwards the DHCP BOOTREQUEST packet to a DHCP server? question 261, answer is D, ip dhcp relay information option Example: Router(config)# ip dhcp relay information option Enables the system to insert the DHCP relay agent information option (option-82 field) in forwarded BOOTREQUEST messages to a DHCP CANADA
Giovani Commented on May 14, 2025 The question bank for practice in this exam is quite decent. I practiced all of them for about 2 weeks and then went for my test. And got my cert on first try. Thank you for this service. CANADA
Abbas Commented on March 24, 2025 Question 42 answer is verify and commit (A and B) Anonymous
Finn Commented on May 04, 2023 I appreciated the mix of multiple-choice and short answer questions. I passed my exam this morning. IRLAND
Finn Commented on May 04, 2023 i appreciated the mix of multiple-choice and short answer questions. i passed my exam this morning. IRLAND
Jack Commented on June 02, 2020 This crisis [the COVID-19 pandemic] has demonstrated the need to be digital-first, agile and could-prepared. Therefore, I have started to get as many could based certificates as I can. With the help of these brain dumps I think it is possible. UNITED KINGDOM