CompTIA
Checkpoint
ISC
HP
Dell
EC-Council
EXIN
Fortinet
ITIL®
Juniper
PMI
Microsoft
VMware
Avaya
Google
Salesforce
Amazon
Palo Alto Networks
Certiport
ISC2
All Vendors
  2. Home
  3. Exams
  4. Network Appliance
  5. NS0-093

Free NS0-093 Exam Braindumps (page: 7)

Page 6 of 17
PDF with 61 Questions

Which LOADER prompt command ensures that POST is done on boot?

  1. setenv POST=true
  2. bye
  3. boot_diag
  4. boot_ontap

Answer(s): A

Explanation:

To ensure that POST (Power-On Self-Test) runs on boot, the setenv POST=true command is used at the LOADER prompt. This command enables the system to perform POST diagnostics before proceeding with the boot process.

Key Details:
POST Purpose: POST checks system hardware components (such as memory, disk, and controllers) for faults before loading the ONTAP kernel.
How to Use:
At the LOADER prompt, type:
arduino
Copy code setenv POST=true
Save the configuration and reboot the system.

Why Other Options Are Incorrect:
B . bye:
This command restarts the system but does not ensure that POST runs on boot.
C . boot_diag:
This command boots the system into diagnostic mode but is not directly related to enabling POST on boot.
D . boot_ontap:
This command boots ONTAP but skips POST if it is not explicitly enabled.


Reference:

NetApp "ONTAP System Boot and Recovery Guide" describes setenv POST=true for enabling POST diagnostics.



In a SAS stack of shelves, what is the topology of the connection between expander and disk?

  1. arbritrated loop
  2. point-to-point
  3. loop
  4. ring

Answer(s): B

Explanation:

In a SAS stack of shelves, the connection between the expander and the disk uses a point-to-point topology.

Key Details:
Point-to-Point:
Each SAS disk in a shelf connects directly to the expander using a dedicated channel. This ensures that communication between the disk and expander is independent of other disks, improving performance and reliability.
Why SAS Uses Point-to-Point:
SAS (Serial Attached SCSI) eliminates the shared bandwidth limitations of traditional bus architectures (e.g., arbitrated loop or ring) by dedicating a connection to each device.

Why Other Options Are Incorrect:
A . arbitrated loop:
Arbitrated loop is a topology used in Fibre Channel systems, not SAS.
C . loop:
SAS does not use loop-based communication; this is typical of older technologies like SCSI Parallel Interface (SPI).
D . ring:
Ring topology is not used in SAS stacks.


Reference:

"NetApp SAS Shelf and Disk Configuration Guide" specifies point-to-point communication between expanders and disks in SAS environments.



Which two statements are correct when describing L1 and L2 Watch Dog Resets (WDR)? (Choose two.)

  1. L2 WDR requests creation of a core dump before reset.
  2. L1 WDR is initiated after 0.5 seconds from the event.
  3. L1 WDR performs a soft reset.
  4. L2 WDR is initiated after 2 seconds from the event.

Answer(s): A,D

Explanation:

1. L1 Watchdog Reset (WDR):
Description:
L1 WDR is a hardware-initiated reset that occurs when the system detects an unrecoverable error or lockup lasting 0.5 seconds.
Key Characteristics:
It performs a hard reset, meaning the system immediately reboots without creating a core dump.

2. L2 Watchdog Reset (WDR):
Description:
L2 WDR is initiated when the system fails to recover from a critical fault after 2 seconds.
Key Characteristics:
It requests a core dump to capture the system state for diagnostic purposes before performing a reset.

Why Other Options Are Incorrect:
B . L1 WDR is initiated after 0.5 seconds from the event:
This is incorrect because L1 WDR performs a hard reset and does not initiate after 2 seconds.
C . L1 WDR performs a soft reset:
This is incorrect because L1 WDR performs a hard reset, not a soft reset.


Reference:

"ONTAP Panic Analysis Guide" describes the behavior and timing of L1 and L2 WDR events. NetApp Support documentation on system resets explains the differences between L1 and L2 watchdog resets.



How do you set environment variables to factory settings?

  1. set-defaults
  2. unsetenv all
  3. setenv factory
  4. wipeconfig

Answer(s): A

Explanation:

To reset environment variables to factory settings, the set-defaults command is used. This command clears all customizations and restores the environment variables to their default values.

Key Details:
Command Syntax:
At the LOADER prompt, type:
arduino
Copy code set-defaults
Effect:
This command resets all environment variables (e.g., boot arguments, diagnostic settings) to their original factory defaults.

Why Other Options Are Incorrect:
B . unsetenv all:
This command clears all environment variables, but it does not restore them to factory defaults.
C . setenv factory:
This is not a valid command in NetApp systems.
D . wipeconfig:
This command is used to clear configuration and logs but does not reset environment variables.


Reference:

NetApp "System Configuration Guide" confirms the use of set-defaults for restoring environment variables to factory settings.






Post your Comments and Discuss Network Appliance NS0-093 exam with other Community members:

NS0-093 Exam Discussions & Posts