Free 200-301 Exam braindumps download (200-301 exam dumps Free)

QUESTION: 426

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

It starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1.
It immediately replaces the existing OSPF route in the routing table with the newly configured static route.
It starts load-balancing traffic between the two default routes.
It ignores the new static route until the existing OSPF default route is removed.

Answer(s): D

Explanation:

Our new static default route has the Administrative Distance (AD) of 120, which is bigger than the AD of OSPF External route (O*E2) so it will not be pushed into the routing table until the current OSPF External route is removed.
For your information, if you don't type the AD of 120 (using the command “ip route 0.0.0.0 0.0.0.0 10.13.0.1”) then the new static default route would replace the
OSPF default route as the default AD of static route is 1. You will see such line in the routing table:
S* 0.0.0.0/0 [1/0] via 10.13.0.1

Show Answer Next Question

QUESTION: 427

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

All of the routers need to be configured for backbone Area 1.
R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
The hello and dead interval timers are not set to the same values on R1 and R3.
EIGRP is also configured on these routers with a lower administrative distance.
R1 and R3 are configured in different areas.

Answer(s): D,F

Explanation:

This question is to examine the conditions for OSPF to create neighborhood. So as to make the two routers become neighbors, each router must be matched with the following items:
1. The area ID and its types
2. Hello and failure time interval timer
3. OSPF Password (Optional)

Show Answer Next Question

QUESTION: 428

Refer to the exhibit. Which command configures a floating static route to provide a backup to the primary link?

ip route 209.165.200.224 255.255.255.224 209.165.202.129 254
ip route 209.165.201.0 255.255.255.224 209.165.202.130
ip route 0.0.0.0 0.0.0.0 209.165.200.224
ip route 0.0.0.0 0.0.0.0 209.165.202.131

Answer(s): A

Show Answer Next Question

QUESTION: 429

Refer to the exhibit. An engineer configured the New York router with static routes that point to the Atlanta and Washington sites. Which command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?

ipv6 route::/0 Serial 0/0/0
ipv6 route::/0 Serial 0/0/1
ipv6 route:0/0 Serial 0/0/0
ip route 0.0.0.0 0.0.0.0 Serial 0/0/0
ipv6 route::/0 2000::2

Answer(s): A

Reference:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_pi/configuration/xe-3s/iri-xe-3s-book/ip6-route-static-xe.html#GUID-85796C3A-3143-4DF7-B9D0-8EC87D0DB08B

Show Answer Next Question