CompTIA
Checkpoint
ISC
HP
Dell
EC-Council
EXIN
Fortinet
ITIL®
Juniper
PMI
Microsoft
VMware
Avaya
Google
Salesforce
Amazon
Palo Alto Networks
Certiport
ISC2
All Vendors
  2. Home
  3. Exams
  4. Cisco®
  5. 300-410

Free 300-410 Exam Braindumps (page: 64)

Page 64 of 156
PDF with 620 Questions

What is a function of IPv6 Source Guard?

  1. It inspects ND and DHCP packets to build an address binding table.
  2. It works with address glean or ND to find existing addresses.
  3. It notifies the ND protocol to inform hosts if the traffic is denied by it.
  4. It denies traffic from known sources and allocated addresses.

Answer(s): B



Refer to the exhibit.



A network engineer must establish communication between three different customer sites with these requirements:

* Site-A: must be restricted to access to any users at Site-B or Site-C.
* Site-B and Site-C: must be able to communicate between sites and share routes using OSPF.

PE interface configuration:
interface FastEthernet0/0
ip vrf forwarding Site-A
!
interface FastEthernet0/1
ip vrf forwarding SharedSites
!
interface FastEthernet0/2
ip vrf forwarding SharedSites

Which configuration meets the requirements?

  1. PE(config)#router ospf 10 vrf Site-A
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0
    PE(config)#router ospf 10 vrf SharedSites
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 1
  2. PE(config)#router ospf 10 vrf Site-A
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0
    PE(config)#router ospf 20 vrf SharedSites
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 1
  3. PE(config)#router ospf 10 vrf Site-A
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0
    PE(config)#router ospf 10 vrf SharedSites
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0
  4. PE(config)#router ospf 10 vrf Site-A
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0
    PE(config)#router ospf 20 vrf SharedSites
    PE(config-router)#network 0.0.0.0 255.255.255.255 area 0

Answer(s): D



What is LDP label binding?

  1. destination prefix with label
  2. two routers with label distribution session
  3. source prefix with label
  4. neighboring router with label

Answer(s): A


Reference:

https://www.cisco.com/en/US/docs/general/Test/kwoodwar/fsinbd4.pdf



Refer to the exhibit. An administrator configures a router to stop using a particular default route if the DNS server 8.8.8.8 is not reachable through that route.


However, this configuration did not work as desired and the default route still works even if the DNS server 8.8.8.8 is unreachable. Which two configuration changes resolve the issue? (Choose two.)

  1. Use a separate track object to reference the existing IP SLA 1 probe for every static route.
  2. Use a separate IP SLA probe and track object for every static route.
  3. Associate every IP SLA probe with the proper WAN address of the router.
  4. Reference the proper exit interfaces along with the next hops in both static default routes.
  5. Configure two static routes for the 8.8.8.8/32 destination to match the IP SLA probe for each ISP.

Answer(s): B,C



Page 64 of 156



Post your Comments and Discuss Cisco® 300-410 exam with other Community members:

Ramu commented on February 24, 2024
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
Anonymous
upvote

Loren commented on August 06, 2021
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
UNITED STATES
upvote

Asaya commented on August 04, 2021
It is looking good. I just made my download. Study begins tomorrow.
BRAZIL
upvote

Kalib commented on April 12, 2021
With my busy schedule this is the best source of studying to pass my exam.
AUSTRALIA
upvote