Free 300-410 Exam Braindumps (page: 67)

Page 67 of 156

Refer to the exhibit.



RR Configuration:
router bgp 100
neighbor IBGP peer-group
neighbor IBGP route-reflector-client
neighbor 10.1.1.1 remote-as 100
neighbor 10.1.2.2 remote-as 100
neighbor 10.1.3.3 remote-as 100

The network administrator configured the network to establish connectivity between all devices and notices that the ASBRs do not have routes for each other.
Which set of configurations resolves this issue?

  1. router bgp 100
    neighbor IBGP update-source Loopback0
  2. router bgp 100
    neighbor IBGP next-hop-self
  3. router bgp 100
    neighbor 10.1.1.1 next-hop-self
    neighbor 10.1.2.2 next-hop-self
    neighbor 10.1.3.3 next-hop-self
  4. router bgp 100
    neighbor 10.1.1.1 peer-group IBGP
    neighbor 10.1.2.2 peer-group IBGP
    neighbor 10.1.3.3 peer-group IBGP

Answer(s): D



Refer to the exhibit. A prefix list is created to filter routes inbound to an EIGRP process except for network 10 prefixes. After the prefix list is applied, no network 10 prefixes are visible in the routing table from EIGRP. Which configuration resolves the issue?

  1. ip prefix-list EIGRP seq 10 permit 0.0.0.0/0 le 32
  2. ip prefix-list EIGRP seq 20 permit 10.0.0.0/8 ge 9 ip prefix-list EIGRP seq 10 permit 0.0.0.0/0 le 32
  3. ip prefix-list EIGRP seq 20 permit 10.0.0.0/8 ge 9
  4. ip prefix-list EIGRP seq 5 permit 10.0.0.0/8 ge 9 no ip prefix-list EIGRP seq 20 permit 10.0.0.0/8

Answer(s): D



Refer to the exhibit. An engineer configured SNMP traps to record spoofed packets drop of more than 48000 a minute on the ethernet0/0 interface. During an IP spoofing attack, the engineer noticed that no notifications have been received by the SNMP server. Which configuration resolves the issue on R1?

  1. ip verify unicast notification threshold 800
  2. ip verify unicast notification threshold 8000
  3. ip verify unicast notification threshold 48000
  4. ip verify unicast notification threshold 80

Answer(s): A


Reference:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_data_urpf/configuration/12-4t/sec-data-urpf-12-4t-book/sec-urpf-mib.html



Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4. How must sequence 20 be replaced on the R1 access list to resolve the issue?

  1. sequence 20 permit tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnet
  2. sequence 20 deny tcp host 400A:0:400C::1 host 1001:ABC:2011:7::1 eq telnet
  3. sequence 20 permit tcp host 400A:0:400C::1 host 1001:ABC:2011:7::1 eq telnet
  4. sequence 20 deny tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnet

Answer(s): D



Page 67 of 156



Post your Comments and Discuss Cisco® 300-410 exam with other Community members:

Ramu commented on February 24, 2024
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
Anonymous
upvote

Loren commented on August 06, 2021
I really do not like relying on these exam dumps questions, but this exam has left me no choice. So I purchased this exam dumps and now I feel much relieved and confident preparing for my exam.
UNITED STATES
upvote

Asaya commented on August 04, 2021
It is looking good. I just made my download. Study begins tomorrow.
BRAZIL
upvote

Kalib commented on April 12, 2021
With my busy schedule this is the best source of studying to pass my exam.
AUSTRALIA
upvote