support@Free-Braindumps.com
Register Login
Cisco
CompTIA
ISC
EC-Council
EXIN
Fortinet
ITIL
Juniper
Microsoft
VMware
Avaya
SAP
Google
NVIDIA
Salesforce
Amazon
Palo Alto Networks
ISC2
CrowdStrike
Anthropic
All Vendors
  1. Home
  2. Exams
  3. Cisco
  4. 350-601

Free 350-601 Exam Braindumps
Implementing and Operating Cisco Data Center Core Technologies (DCCOR) Questions 121–125 (page: 26)

Updated On: 10-Feb-2026
Page 26 of 106
PDF with 584 Questions

Refer to the exhibit. Which type of backup is required to restore a Cisco UCS configuration?

  1. system configuration
  2. all configuration
  3. full state
  4. logical configuration

Answer(s): C

Explanation:


Reference:

https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/141/UCSM_GUI_Configuration_Guide_141_chapter43.html



Which server policy is used to install new Cisco IMC software on a server?

  1. hypervisor firmware policy
  2. host firmware policy
  3. BIOS software policy
  4. Cisco IMC software policy

Answer(s): B

Explanation:


Reference:

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/CLI-User-Guides/Firmware-Mgmt/4-0/ b_UCSM_CLI_Firmware_Management_Guide_4-0/b_UCSM_CLI_Firmware_Management_Guide_4-0_chapter_01.html



What are two requirements when planning a Cisco HyperFlex All Flash standard cluster installation using three Cisco HX240c M5 Series servers? (Choose two.)

  1. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames do not have to be enabled on the upstream switches.
  2. This cluster deployment type must support a mix of HDD and SSD.
  3. The servers must be discovered, unassociated, and connected to each fabric interconnect.
  4. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames must also be enabled on the upstream switches.
  5. The hypervisors must be installed to Cisco FlexFlash SD cards.

Answer(s): C,D

Explanation:


Reference:

https://www.cisco.com/c/en/us/td/docs/hyperconverged_systems/HyperFlex_HX_DataPlatformSoftware/AdminGuide/3_5/ b_HyperFlexSystems_AdministrationGuide_3_5/b_HyperFlexSystems_AdministrationGuide_3_5_chapter_01111.html



Refer to the exhibit. Service degradation is reported on a VM that is deployed on a Cisco UCS B-Series Server. The traffic from the vNIC is required to SPAN in both directions to a packet analyzer that is connected to UCS-A slot 2 port 12. Which two commands are needed to complete the configuration? (Choose two.)

  1. UCS-A /org/service-profile/vnic/mon-src* # set direction receive transmit
  2. UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12
  3. UCS-A /eth-traffic-mon/fabric/eth-mon-session # activate
  4. UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create eth-mon-session/dest-interface 2 12
  5. UCS-A /org/service-profile/vnic/mon-src* # set direction both

Answer(s): B,E

Explanation:


Reference:

https://www.cisco.com/en/US/docs/unified_computing/ucs/sw/cli/config/guide/1.4.1/CLI_Config_Guide_1_4_1_chapter42.html



An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?

  1. The system defaults to and boots into kickstart image
  2. The system defaults to and boots into GOLD firmware image
  3. The system defaults to the GOLD firmware image
  4. The system defaults to the backup image version

Answer(s): D

Explanation:


Reference:

https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/CLI-User-Guides/Firmware-Mgmt/4-0/ b_UCSM_CLI_Firmware_Management_Guide_4-0/b_UCSM_CLI_Firmware_Management_Guide_4-0_chapter_011.html



  PDF
Viewing page 26 of 106
Viewing questions 126 - 130 out of 584 questions


Post your Comments and Discuss Cisco 350-601 exam prep with other Community members:

AI Tutor AI Tutor 👋 I’m here to help!